Bedienungsanleitung Sigma 120-400mm f4.5-5.6 APO DG OS HSM (Seite 1 von 2) (Englisch)

616759

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Thank you very much for purchasing a Sigma Lens. In order to get the maximum

performance and enjoyment out of your Sigma lens, please read this instruction

booklet thoroughly before you start to use the lens.

DESCRIPTION OF THE PARTS (fig.1)

NIKON AF TYPE CAMERAS

This lens functions in the same way as a G Type auto-focus Nikon lens (without

an aperture ring). Functions may be restricted depending on the lens/camera

combination. For more details, please refer to the camera’s instruction manual.

PENTAX AF TYPE CAMERAS

This Lens functions same as a FAJ Type (type without Aperture) auto-focus

Pentax lens. Depending on the combination with camera some restrictions with

its functions may result. For more details, please refer to instruction manual of

the camera in use etc.

ATTACHING TO CAMERA BODY

When this lens is attached to the camera body it will automatically function in the

same way as the camera manufacturer’s lens. Please refer to the instruction

booklet for your camera body.

◆ On the lens mount surface, there are a number of couplers and electrical

contacts. Please keep them clean to ensure proper connection.

◆

While changing the lens, be sure to place it front end down to avoid damaging the

rear mount.

SETTING THE EXPOSURE MODE

The Sigma lens functions automatically once attached to the camera. Please

refer to the camera instruction book.

FOCUSING AND ZOOMING

This lens features Sigma’s built-in Hyper Sonic Motor (HSM). The HSM

enables quick and quiet autofocusing.

《

SIGMA AF and CANON AF

》

For autofocus operation, set the focus mode switch on the lens to the “AF”

position (fig.2). If you wish to focus manually, set the focus mode switch on the

lens to the “M” position. You can adjust the focus by turning the focus ring.

《

NIKON AF, PENTAX AF, and SONY

》

For autofocus operation, set the camera to AF mode and set the focus mode

switch on the lens to the “AF” position (fig.2). If you wish to focus manually, set

the focus mode switch on the lens to the “M” position. You can adjust the focus

by turning the focus ring.

◆ Please refer to camera’s instruction manual for details on changing the

camera’s focusing mode.

◆ For Nikon, Pentax and Sony mounts, it is only possible to use AF with camera

bodies which support motors driven by ultrasonic waves such as HSM. AF

will not function if the camera body does not support this type of motor.

◆ This lens also permits manual focusing even in the autofocus mode. With

the camera set to the One-Shot AF (AF-S) mode, it is possible to manually

override the autofocus while the shutter release button is pressed halfway.

◆ When operating this lens in manual focus mode, it is recommended that

correct focus be confirmed visually in the viewfinder rather than relying on the

distance scale. This is due to possible focus shift resulting from extreme

changes in temperature which cause various components in the lens to

expand and contract. Special allowance is made for this at the infinity

setting.

《Zooming》

Rotate the Rubber grip on the zoom ring to the desired position.

ZOOM LOCK SWITCH

This lens is also equipped with Zoom Lock Switch to eliminate the zoom creep

when the lens is tilted down. Please set zooming ring to 120mm and set the

zoom lock switch to the “LOCK” position, (fig.3), however, please slide the lens

to the “UNLOCK” position from “LOCK” position, before taking the picture.

ABOUT OS (OPTICAL STABILIZER) FEATURES

(except Pentax AF and SONY mount)

This OS

(Optical Stabilizer)

lens effectively compensates for image blurring

caused by camera shake.

With this lens, you can take pictures at shutter speeds approx 4 steps slower

than you could without using the OS function of this lens and can get sharp

results.

Set the OS（Optical Stabilizer）switch to Mode 1 (fig. 4). Press the shutter button

halfway down, confirm the image in the viewfinder is stable then take the picture.

(It takes approximately 1 second to produce a stable image, after pressing the

shutter button halfway). Mode

, detects the vertical camera shake, and

overcomes blurring. It is effective on subjects moving horizontal to the camera.

◆ The blurring compensation function of Optical Stabilizer is effective for

hand-held shooting. In the following conditions, Optical Stabilizer may not

function properly.

▪ Shots from the a moving vehicle ▪ If there is a considerable camera motion

or shake.

◆ Please do not use Optical Stabilizer in the following situations.

▪ When the lens is mounted on a tripod. ▪ Bulb (long time exposure).

◆ Optical Stabilizer function is powered from the camera. If the OS lens is

attached to your camera and activated, shooting capacity of your camera will

be lower than with conventional lenses used with the same camera. If you are

not using Optical Stabilizer, please turn OFF the OS switch, in order to prevent

consumption of a battery.

◆ Be sure to turn of OS switch to OFF position, before attaching or detaching

the lens to the camera.

◆ The Optical Stabilizer continues to operate after you release your finger from

the shutter button, as long as the exposure meter displays the exposure value.

Never remove the lens or remove the camera’s battery while the image

stabilizer is operating, you could damage the lens.

◆

Although the viewfinder image may appear to shake immediately after shooting

and at the start of the flash charge cycle of the built-in flash of the camera etc., it

will not cause any effect on pictures.

◆ If the camera power is turned off or lens is detached while the Optical

Stabilizer function is in operation, the lens may emit a chattering noise, but this

is not a malfunction.

◆ Optical Stabilizer feature can work with the Nikon AF cameras shown in the

following table. When using this lens with other camera models not listed in

the following table, please set the OS Switch to OFF position to cancel the

Optical Stabilizer function.

Digital SLR Cameras and F6, F5, F100, F80/N80, U (F65/N65), U2 (F75/N75)

※From our homepage, you can check the latest information regarding the

camera models, which can be used with Optical Stabilizer function.

TRIPOD SOCKET AND COLLAR

This lens is equipped with a tripod socket. When you loosen the locking knob on the

collar, the lens and camera can rotate freely to easily position the camera

horizontally or vertically (fig.5).

HOW TO REMOVE THE TRIPOD COLLAR

1. It is possible to remove the lens’ tripod socket, for more convenient hand-held

photography, if desired. To do so, first loosen the tripod collar locking knob,

and, align the index mark of the collar, with the ▼REMOVE position (fig.6).

2. Then, pull the tripod collar straight back, as shown in Fig.7, removing the

collar.

◆

When you wish to re-attach the tripod collar to the lens, please reverse the

procedure above.

◆ Please, do not set the tripod collar to the ▼REMOVE position, except when

you are removing, or attaching, the tripod collar, as the lens may inadvertently

detach from the collar and fall. Also, please remember to tighten the locking

knob to prevent the lens from rotating unintentionally.

◆

When the lens is mounted on the camera, the tripod collar cannot be removed

from the lens.

SHOULDER STRAP

Please attach the shoulder strap to the sling as described in figure 8.

FLASH PHOTOGRAPHY

The camera’s built-in flash will cause barrel shadow if used with this lens. For

best results, please only use an external flash unit.

ABOUT TELE CONVERTERS

The lens can be used with Sigma’s 1.4x EX or 2.0x EX Apo Tele Converters

(optional), becoming a 168-560mm F6.3-8 telephoto zoom lens or a 240-800mm

F9-11 telephoto zoom lens respectively （both can be used in manual focus

only）.

◆ Do not use other manufacturers’ teleconverter’s, only those listed above are

compatible.

◆ The Pentax mount Tele Converter is not compatible with this particular lens.

◆ We recommend the DG APO Tele-Converters when using with DSLR

cameras.

LENS HOOD

A bayonet type detachable `hood is provided with the lens. This lens hood

helps to prevent flare and ghosted images caused by extraneous light. Attach

the hood and turn clockwise until it stops rotating. (fig.9)

◆ In order to place the lens and hood into the storage case, you must first

remove the hood, then replace it on the lens in the reverse position. (fig.10)

FILTER

◆ Only one filter should be used at a time. Two or more filters and/or special,

thicker filters, such as a polarizing filter, may cause vignetting.

◆ When using a polarizing filter with an AF camera, use the “circular” type.

BASIC CARE AND STORAGE

◆ Avoid any shocks or exposure to extreme high or low temperatures or to

humidity.

ENGLISH

 Zoom Lock Switch

 OS Switch

(except Pentax AF and SONY mount)

 Lens Hood

① Filter Attachment Thread

② Focus Ring

③ Distance Scale

④ Focus Index Line

 Zoom Ring

 Focus Mode Switch

 Mount

 Tripod Socket

Sigma 120-400mm f4.5-5.6 APO DG OS HSM Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info