Bedienungsanleitung Sigma 18-50mm f3.5-5.6 DC (Seite 1 von 1) (Englisch)

616741

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Thank you very much for purchasing a Sigma Lens. In order to get the maximum

performance and enjoyment out of your Sigma lens, please read this instruction booklet

thoroughly before you start to use the lens.

DESCRIPTION OF THE PARTS (fig.1)

① Filter Attachment Thread

② Focus Ring

③ Distance Scale

④ Focus Index Line

⑤ Zoom Ring

⑥ Focus Mode Switch (SIGMA SA / CANON AF / NIKON / FOUR THIRDS)

⑦ Mount

⑧ Lens Hood

DC LENS

These are special lenses that are designated for digital cameras because the lens image

circle is designated to correspond to the size of the image sensors of most digital SLR

cameras. The specialized design gives these lenses the ideal properties for digital cameras.

◆ An image sensor element larger than those corresponding to APS-C cannot be used in

digital cameras or 35mm SLR cameras. If such an element is used vignetting will occur

on the picture surface.

◆ If you use SD14 / SD10 / SD9 digital cameras, corresponding angle of view will be

30-85mm.

ATTACHING TO CAMERA BODY

When this lens is attached to the camera body it will automatically function in the same way

as your normal lens. Please refer to the instruction booklet for your camera body.

◆ On the lens mount surface, there are a number of couplers and electrical contacts.

Please keep them clean to ensure proper connection. To avoid damaging the lens, be

especially sure to place the lens with its front end down while changing the lens.

◆ Many accessories such as rear mounted teleconverters, extension tubes, etc., are

specially made for designated lenses. Before you purchase such accessories, please

check your Sigma lens to determine that it is compatible and that the accessories will

function properly with it.

SETTING THE EXPOSURE MODE

The sigma lens functions automatically after mounting to your camera. Please, refer to the

camera instruction book.

FOCUSING AND ZOOMING

《

SIGMA AF and CANON AF

》

For autofocus operation, set the focus mode switch on the lens to the “AF” position (fig.2). If

you wish to focus manually, set the focus mode switch on the lens to the “M” position. You

can adjust the focus by turning the focus ring.

《

NIKON AF and FOUR THIRDS

》

For autofocus operation, set the camera to AF mode and set the focus mode switch on the

lens to the “AF” position (fig.2). If you wish to focus manually, set the focus mode switch on

the lens to the “M” position. You can adjust the focus by turning the focus ring. (In the case

of Four-Thirds cameras it is necessary to switch the camera to MF mode as well)

《

SONY AF and PENTAX AF

》

For autofocus operation, set the camera’s focus mode to AF. If you wish to focus manually,

set the camera’s focus mode to “M” and adjust the focus by turning the focus ring.

◆ Please refer to camera’s instruction manual for details on changing the camera’s

focusing mode.

◆ The viewfinder of some Nikon AF cameras have indicators to display the focus status.

The “● ” symbol indicates that correct focus has been set, “

► ” indicates that focus is

set in front of the subject, and “

◄” indicates that focus is set behind the subject. When

this AF lens is used with Nikon AF cameras in MF mode, please adjust the lens’ focus

until the “● ” symbol is visible.

◆ To avoid damaging AF mechanism, please do not turn the focus ring manually while in

the autofocus mode.

◆ When operating this lens in manual focus mode, it is recommended that correct focus be

confirmed visually in the viewfinder rather than relying on the distance scale. This is

due to possible focus shift resulting from extreme changes in temperature which cause

various components in the lens to expand and contact. Special allowance is made for

this at the infinity setting.

◆ In the case of Four Thirds lenses, the function of AF-S mode with MF override is not

available.

《

Zooming

》

Rotate the Rubber grip on the zoom ring to the desired position.

LENS HOOD

A bayonet type detachable hood is provided with the lens. This lens hood helps to prevent

flare and ghosted images caused by bright illumination from outside the picture area.

Attach the hood and turn clockwise until it stops rotation. (fig.3)

◆ When taking photographs using the built-in flash, it is advisable to remove the lens hood

so as to avoid cutting off any of the flash output, which could cause a shadow in the

picture.

◆ In order to place the lens and hood into the storage case, you must first remove the

hood, then replace it on the lens in the reverse position. (fig.4)

FILTER

◆ When mounting or removing the filter, the lens should be in the manual focus mode, and

should be held by the front of the lens barrel in order to avoid damaging the lens and

camera (fig.5).

◆ Only one filter should be used at the time. Two or more filters and/or special thicker

filters, like a polarizing filter, may cause vignetting.

◆ When using a polarizing filter with AF camera, use the “circular” type.

BASIC CARE AND STORAGE

◆ Avoid any shocks or exposure to extreme high or low temperatures or to humidity.

◆ For extended storage, choose a cool and dry place, preferably with good ventilation. To

avoid damage to the lens coating, keep away from mothballs or naphthalene gas.

◆ Do not use thinner, benzine or other organic cleaning agents to remove dirt or finger

prints from the lens elements. Clean by using a soft, moistened lens cloth or lens

tissue.

◆ This lens is not waterproof. When you use the lens in the rain or near water, keep it

from getting wet. It is often impractical to repair the internal mechanism, lens elements

and electric components damaged by water.

◆ Sudden temperature changes may cause condensation or fog to appear on the surface

of the lens. When entering a warm room from the cold outdoors, it is advisable to keep

the lens in the case until the temperature of the lens approaches room temperature.

TECHNICAL SPECIFICATIONS

Lens construction 8 - 8

Angle of View 69.3 – 27.9°

Minimum Aperture 22

Minimum Focusing Distance 25cm (0.82 ft)

Magnification 1:3.5

Filter Size 58mm

Dimensions Dia.×Length 67.5×62mm (2.66×2.44 in)

Weight 250g (8.8 oz)

Dimensions and weight include the SIGMA mount.

The CE Mark is a Directive conformity mark of the European

Community (EC).

SIGMA (Deutschland) GmbH

Carl-Zeiss-Str. 10/2, D-63322 Rödermark, F.R.GERMANY

Verkauf: 01805-90 90 85-0 Service: 01805-90 90 85-85 Fax: 01805-90 90 85-35

ENGLISH

Sigma 18-50mm f3.5-5.6 DC Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info