Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
WL-358/359/363/367
Wireless ADSL2+ router
Annex-A (WL-358,WL-359,WL-363) & Annex-B (WL-367)
User Manual
Version: 1.0
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    WL-358/359/363/367

    Wireless ADSL2+ router
    Annex-A (WL-358,WL-359,WL-363) & Annex-B (WL-367)

    User Manual
    Version: 1.0



  • Page 2

    TABLE OF CONTENTS
    1

    KEY FEATURES .................................................................................................................... 4

    2

    PACKAGE CONTENTS ....................................................................................................... 5

    3

    PRODUCT LAYOUT............................................................................................................. 6

    4

    SYSTEM REQUIREMENTS............................................................................................... 8

    5

    MODEM/ROUTERPLACEMENT ..................................................................................... 9

    6

    SETUP LAN, WAN ............................................................................................................... 9

    7

    PC NETWORK ADAPTER SETUP................................................................................ 10

    8

    BRINGING UP THE WL-358/359/363/367 ...................................................... 13

    9

    INITIAL SETUP WL-358/359/363/367 ............................................................. 13

    10

    CONFIGURATION WIZARD......................................................................................... 23

    11

    WIRELESS SETTINGS .................................................................................................... 25

    12

    FIREWALL SETTINGS .................................................................................................... 35

    13

    ADVANCED SETTINGS................................................................................................... 42

    14

    TOOLBOX SETTINGS ...................................................................................................... 54



  • Page 3

    Introduction
    Congratulations on your purchase of the WL-358,359,363 or 367 Wireless
    ADSL2+ Modem. The Modem is fully compliant with 802.11n. This modem is
    also fully compliant with 802.11g & 802.11b. This modem provide the best
    performance when used in combination with 802.11n client adapters.
    The WL-358,359,363 or 367 is not only a Modem or Wireless Access Point,
    but can also be used to connect wired-Ethernet devices.

    For data protection and privacy, the modem can encode all wireless
    transmissions with WEP, WPA, and WPA2 encryption. By default, the modem
    is secured with a WPA2(AES) encryption key. (The WPA2-key is printed on the
    label underneath the modem.)

    With a built-in DHCP Server & powerful SPI firewall the modem protects your
    computers against intruders and known Internet attacks, and also provides
    safe VPN pass-through.



  • Page 4

    1 Key Features
    Features
    IEEE 802.11b/g/n compliant

    Advantages
    Fully Interoperable with IEEE
    802.11b / IEEE802.11g /802.11n
    compliant devices

    Four 10/100 Mbps Fast Ethernet

    To connect four wired PC's as well.

    Port (Auto-Crossover)
    Firewall supports Virtual Server

    Avoids the attacks of Hackers or

    Mapping, DMZ, IP Filter, ICMP

    Viruses from Internet

    Blocking, SPI
    Support 802.1x authenticator,

    Provide mutual authentication

    802.11i (WPA/WPA2, AES), VPN

    (Client and dynamic encryption keys

    pass-through

    to enhance security

    Integrated modem (Annex B)

    Fully compatible with the fastest
    ADSL2+ connections up-to-date.



  • Page 5

    2 Package Contents
    Open the package carefully, and make sure that none of the items listed
    below are missing. Do not discard the packing materials, in case of return;
    the unit must be shipped back in its original package.

    1.

    WL-358,359,363 or 367 modem/router

    2.

    220V ~ 240V Power Adapter

    3.

    Quick Install Guide

    4.

    CD (User’s Manual)

    5.

    Warranty card

    6.

    UTP cable



  • Page 6

    3 Product Layout

    WPS/Reset button

    Power button

    Modem connection

    Power connector

    LAN / computer connections

    Port

    Description

    ADSL

    Connect your telephone/ADSL cable this port
    Connect the cable from your PC or network device
    to this ports.

    LAN
    Power
    connector
    Power button

    Connect your power adapter to this port.
    Turn the modem On or Off.



  • Page 7

    Back label
    The back label describes the corresponding LED indications and port functionality.

    LED

    Description

    Power

    Lights up when powered ON. Blinks on
    TEST/RESET

    ADSL

    Lights up when an ADSL cable is
    connected.

    Internet

    Lights up when internet connection is UP.

    WLAN

    Lights up in Blue when WLAN is enabled.
    Blinks on traffic

    OPS

    Blinks when OPS mode is on

    LAN1~4

    When a LAN cable is connected the
    corresponding light lights up.



  • Page 8

    4 System Requirements
    To begin using the WL-358/359/363/367, make sure you meet the
    following as minimum requirements:



    PC/Notebook.



    1 Free Ethernet port.



    Wi-Fi card/USB dongle (802.11 b/g/n) – optional.



    Annex B, ADSL internet connection.



    PC with a Web-Browser (Internet Explorer, Safari, Firefox,
    Opera)



    Ethernet compatible CAT5 cables.



  • Page 9

    5 MODEM/ROUTER Placement
    You can place the modem on a desk or other flat surface, or you can
    mount it on a wall. For optimal performance, place your Wireless
    Broadband Modem/Router in the center of your office (or your home)
    in a location that is away from any potential source of interference,
    such as a metal wall or microwave oven. This location must be close to
    a power connection and the ADSL/phone line should not be over 2
    meters long.

    6 Setup LAN, WAN

    Modem connection
    LAN / computer connections



  • Page 10

    7 PC Network Adapter setup
    Windows XP


    Go to [Start Menu],

    [Control panel],

    [Network Connections].



    Right-mouse-click on the [Local Area Connection]) icon, and select
    [properties]



    Select [Internet Protocol (TCP/IP)] =>Click [Properties].



    Select the [General] tab.
    The Modem/Router supports DHCP. Please select both [Obtain an IP
    address automatically] and [Obtain DNS server address automatically].



  • Page 11

    Windows Vista/Windows 7


    Go to [Start Menu],

    [Control panel],

    [View network status and

    tasks], -> [Manage network connections].



    Right-mouse-click on the [Local Area Connection]) icon, and select
    [properties]



  • Page 12



    Select [Internet Protocol Version 4 (TCP/IPv4)], and Click [Properties].



    Open the [General] tab.
    The Modem/Router supports DHCP. Please select both [Obtain an IP
    address automatically] and [Obtain DNS server address automatically].



  • Page 13

    8 Bringing up the Modem/Router
    Connect the supplied power-adapter to the power inlet port and connect it to
    a wall outlet. Press the Power-Button to turn the modem on.
    The WL-358/359/363 automatically enters the self-test phase. During self-test
    phase, the Power LED will blink briefly, and then will be lit continuously to
    indicate that this product is in normal operation.

    9 Initial Setup Modem/Router
    LOGIN procedure
    1. OPEN your browser (e.g. Internet Explorer).

    2. Type http://192.168.0.1 in address bar and press [Enter]



  • Page 14

    4. Type user name and password (default is admin/admin).

    3. Click OK.
    4. You will see the home page of the WL-358/359/363/367.

    The System status section allows you to monitor the current status of your
    router: the UP time, hardware information, serial number as well as firmware
    version information is displayed here.



  • Page 15

    LAN settings
    The LAN tab gives you the opportunity to change the IP settings of the WL358/359/363/367.

    Click <Apply> at the bottom of this screen to save any changes.

    IP address 192.168.0.1. It is the router’s LAN IP address (Your LAN clients
    default gateway IP address).

    IP Subnet Mask 255.255.255.0 Specify a Subnet Mask for your LAN
    segment.

    DHCP Server Enabled by default. You can enable or disable the DHCP server.
    When DHCP is disabled no ip-addresses are assigned to clients and you have
    to use static ip-addresses. When DHCP server is enabled your computers will
    be assigned an ip-address automatically until the lease time expires.

    Lease Time Forever. In the Lease Time setting you can specify the time
    period that the DHCP lends an IP address to your LAN clients. The DHCP will
    change your LAN client’s IP address when this time threshold period is
    reached.



  • Page 16

    IP Address Pool You can select a particular IP address range for your DHCP
    server to issue IP addresses to your LAN Clients.
    Note: default IP range 192.168.0.100 

    192.168.0.199. If you want

    your PC(s) to have a static/fixed IP address, then you’ll have to
    choose an IP address outside this IP address Pool

    Domain Name You can specify a Domain Name for your LAN. Or just keep
    the default (SitecomWLxxx).



  • Page 17

    Device Status
    View the Broadband modem/router’s current configuration settings. Device
    Status displays the configuration settings you’ve configured in the Wizard /
    Basic Settings / Wireless Settings section.



  • Page 18

    Internet Status
    This page displays whether the ADSL port is connected to an ADSL service
    provider. It also displays the router’s WAN IP address, Subnet Mask, and ISP
    Gateway as well as MAC address, the Primary DNS. Press Renew button to
    renew your WAN IP address.



  • Page 19

    DHCP Client Status
    DHCP This page shows all DHCP clients (LAN PCs) currently connected to your
    network. The table shows the assigned IP address, MAC address and expiration
    time for each DHCP leased client.

    Use the Refresh button to update the available information.



  • Page 20

    Modem/Router Log
    View the operation log of the WL-358/359/363/367. This page shows the
    current system log of the Broadband modem/router. It displays any event
    occurred after system start up. At the bottom of the page, the system log can be
    saved <Save> to a local file for further processing or the system log can be
    cleared <Clear> or it can be refreshed <Refresh> to get the most updated
    information. When the system is powered down, the system log will disappear if
    not saved to a local file.



  • Page 21

    Statistics
    This page shows the statistics for the wireless, LAN, and WAN interfaces.



  • Page 22

    ADSL Status
    This page shows the current operation mode, status of your ADSL connection, the
    data rate and the quality of your ADSL link.

    Operation mode allows manual selection of the ADSL mode.



  • Page 23

    10 Configuration Wizard
    Click Wizard to configure the modem. The Setup wizard will now be displayed;
    check that the adsl line is connected and click Next.

    Select your country from the Country list. Select your internet provider. Click
    Next.



  • Page 24

    Depending on the chosen provider, you may need to enter your user name and
    password or hostname in the following window. After you have entered the
    correct information, click Next.

    Click APPLY to complete the configuration.



  • Page 25

    11

    Wireless Settings

    You can set parameters that are used for the wireless stations to connect to
    this router. The parameters include Mode, ESSID, Channel Number and
    Associated Client.

    Wireless Function

    Enable or Disable Wireless function here. Click Apply and wait for module to
    be ready & loaded.



  • Page 26

    Basic Settings

    802.11 Mode Allows you to set the AP fixed at 802.11b or 802.11g mode.
    You can also select B+G+N mode to allow 802.11b, 802.11g and 802.11n
    clients at the same time.
    Band 20/40 MHz Allows automatic detection of the operation bandwidth
    between 20 and 40 MHz.

    ESSID This is the name of the wireless signal which is broadcasted. All the
    devices in the same wireless LAN should have the same ESSID.
    Channel Number The channel used by the wireless LAN. All devices in the
    same wireless LAN should use the same channel.
    Extension channel This is the optional channel for use. Setting the
    Bandwidth to 20/40 MHz allows you to use this extension channel as the
    secondary channel for doubling the bandwidth of your wireless network.



  • Page 27

    Advanced Settings
    This tab allows you to set the advanced wireless options. The options included
    are

    Authentication

    Type,

    Fragment

    Threshold,

    RTS

    Threshold,

    Beacon

    Interval, and Preamble Type. You should not change these parameters unless
    you know what effect the changes will have on the router.

    Fragment Threshold "Fragment Threshold" specifies the maximum size of a
    packet during the fragmentation of data to be transmitted. If you set this
    value too low, it will result in bad performance.
    RTS Threshold When the packet size is smaller then the RTS threshold, the
    wireless router will not use the RTS/CTS mechanism to send this packet.
    Beacon Interval is the interval of time that this wireless router broadcasts a
    beacon. A Beacon is used to synchronize the wireless network.
    DTIM period is a countdown mechanism for WLAN Access Points changing
    this value will affect your wireless performance and may improve stability.
    Preamble Type The “Long Preamble” can provide better wireless LAN
    compatibility while the “Short Preamble” can provide better wireless LAN
    performance.
    Broadcast ESSID If you enabled “Broadcast ESSID”, every wireless station
    located within the coverage of this access point can discover this access point



  • Page 28

    easily. If you are building a public wireless network, enabling this feature is
    recommended. Disabling “Broadcast ESSID” can provide better security.
    Tx Power Use this option to adjust the transmit power of the wireless
    interface.
    WMM Wi-Fi Multi Media if enabled supports QoS for experiencing better
    audio, video and voice in applications.



  • Page 29

    Security
    This Access Point provides complete wireless LAN security functions, included
    are WEP, WPA with pre-shared key and WPA2 with pre-shared key. With these
    security functions, you can prevent illegal access to your wireless LAN. Please
    make sure your wireless stations use the same security function, and are
    setup with the same security key.

    Disable
    When you choose to disable encryption, it is very insecure to operate the WL358/359/363/367.



  • Page 30

    WEP
    When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to
    encrypt data. You can generate the key by yourself and enter it. You can
    enter four WEP keys and select one of them as a default key. Then the router
    can receive any packets encrypted by one of the four keys.
    Key Length You can select the WEP key length for encryption, 64-bit or 128bit. The larger the key will be the higher level of security is used, but the
    throughput will be lower.
    Key Format You may select ASCII Characters (alphanumeric format) or
    Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.
    Key1 - Key4 The WEP keys are used to encrypt data transmitted in the
    wireless network. Use the following rules to setup a WEP key on the device.
    64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or
    5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit
    Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters
    as the encryption keys.

    Click <Apply> at the bottom of the screen to save the above configurations.
    You can now configure other sections by choosing Continue, or choose Apply
    to apply the settings and reboot the device.



  • Page 31

    WPA Pre-shared Key
    Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a
    pre-shared key to authenticate wireless stations and encrypt data during
    communication. It uses TKIP or CCMP (AES) to change the encryption key
    frequently. So the encryption key is not easy to be cracked by hackers. This is
    the best security available.



  • Page 32

    ACL
    This

    wireless

    router

    supports

    MAC

    Address

    Control,

    which

    prevents

    unauthorized clients from accessing your wireless network.

    Enable wireless access control Enables the wireless access control function
    Adding an address into the list Enter the "MAC Address” of the wireless
    station to be added and then click "Apply". The wireless station will now be
    added. If you are having any difficulties filling in the fields, just clear the MAC
    Address.



  • Page 33

    WPS
    Wi-Fi Protected Setup (WPS) is the simplest way to establish a connection
    between the wireless clients and the wireless router. You don’t have to select
    the encryption mode and fill in a long encryption passphrase every time when
    you try to setup a wireless connection. You only need to press a button on
    both wireless client and wireless router, and WPS will do the rest for you.

    The wireless router supports two types of WPS: WPS via Push Button and
    WPS via PIN code. If you want to use the Push Button, you have to push a
    specific button on the wireless client or in the utility of the wireless client to
    start the WPS mode, and switch the wireless router to WPS mode. You can
    simply push the WPS button of the wireless router, or click the ‘Start to
    Process’ button in the web configuration interface. If you want to use the PIN
    code, you have to know the PIN code of the wireless client and switch it to
    WPS mode, then fill-in the PIN code of the wireless client through the web
    configuration interface of the wireless router.

    WPS Check the box to enable WPS function and uncheck it to disable the
    WPS function.



  • Page 34

    WPS Current Status If the wireless security (encryption) function of this
    wireless router is properly set, you’ll see a ‘Configured’ message here.
    Otherwise, you’ll see ‘UnConfigured’.

    Self Pin Code This is the WPS PIN code of the wireless router. You may need
    this information when connecting to other WPS-enabled wireless devices.

    SSID This is the network broadcast name (SSID) of the router.

    Authentication Mode It shows the active authentication mode for the
    wireless connection.

    Passphrase Key It shows the passphrase key that is randomly generated by
    the wireless router during the WPS process. You may need this information
    when using a device which doesn’t support WPS.

    WPS via Push Button Press the button to start the WPS process. The router
    will wait for the WPS request from the wireless devices within 2 minutes.

    WPS via PIN You can fill-in the PIN code of the wireless device and press the
    button to start the WPS process. The router will wait for the WPS request
    from the wireless device within 2 minutes.



  • Page 35

    12 Firewall Settings
    The Broadband router provides extensive firewall protection by restricting
    connection parameters, thus limiting the risk of hacker attacks, and defending
    against a wide array of common Internet attacks. However, for applications
    that require unrestricted access to the Internet, you can configure a specific
    client/server as a Demilitarized Zone (DMZ).

    Note: To enable the Firewall settings select Enable and click
    Apply.



  • Page 36

    DMZ
    If you have a client PC that cannot run an Internet application (e.g. Games)
    properly from behind the NAT firewall, then you can open up the firewall
    restrictions to unrestricted two-way Internet access by defining a DMZ Host.
    The DMZ function allows you to re-direct all packets going to your WAN port
    IP address to a particular IP address in your LAN. The difference between the
    virtual server and the DMZ function is that the virtual server re-directs a
    particular service/Internet application (e.g. FTP, websites) to a particular LAN
    client/server, whereas DMZ re-directs all packets (regardless of services)
    going to your WAN IP address to a particular LAN client/server.

    Enable DMZ Enable/disable DMZ
    Host Fill in the IP address of a particular host in your LAN that will receive all
    the packets originally going to the WAN port/Public IP address above.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 37

    Denial of Service (DoS)
    The Broadband router's firewall can block common hacker attacks, including
    Denial of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks
    occur the router can log the events.

    SPI and Anti-Dos firewall protection blocks basic hacker attacks (DOS,
    Sync flood, port scan)

    RIP defect

    Discard Ping to WAN interface The router’s WAN port will not respond to
    any Ping requests

    Stateful packet inspection allows the user to manually determine which
    packets should be scanned.



  • Page 38

    Access
    You can restrict users from accessing certain Internet applications/services
    (e.g. Internet websites, email, FTP etc.). Access Control allows users to define
    the traffic type permitted in your LAN. You can control which PC client can
    have access to these services.

    Deny If you select “Deny” then all clients will be allowed to access Internet
    accept for the clients in the list below.

    Allow If you select “Allow” then all clients will be denied to access Internet
    accept for the PCs in the list below.

    Filter client PCs by IP Fill in “IP Filtering Table” to filter PC clients by IP.

    Add PC You can click Add PC to add an access control rule for users by IP
    addresses.

    Remove PC If you want to remove some PCs from the "IP Filtering Table",
    select the PC you want to remove in the table and then click “Delete
    Selected". If you want to remove all PCs from the table, just click the "Delete
    All" button.



  • Page 39

    Filter client PC by MAC Check “Enable MAC Filtering” to enable MAC
    Filtering.

    Add PC Fill in “Client PC MAC Address” and “Comment” of the PC that is
    allowed to access the Internet, and then click “Add”. If you find any typo
    before adding it and want to retype again, just click "Reset" and the fields will
    be cleared.

    Remove PC If you want to remove some PC from the "MAC Filtering Table",
    select the PC you want to remove in the table and then click "Delete
    Selected". If you want to remove all PCs from the table, just click the "Delete
    All" button. If you want to clear the selection and re-select again, just click
    “Reset”.

    Click <Apply> at the bottom of the screen to save the above configuration.



  • Page 40

    URL block
    You can block access to some Web sites from particular PCs by entering a full
    URL address or just keywords of the Web site.

    Enable URL Blocking Enable/disable URL Blocking

    Add URL Keyword Fill in “URL/Keyword” and then click “Add”. You can enter
    the full URL address or the keyword of the web site you want to block.

    Remove URL Keyword If you want to remove some URL keywords from the
    "Current URL Blocking Table", select the URL keyword you want to remove in
    the table and then click "Delete Selected". If you want remove all URL
    keywords from the table, just click "Delete All" button. If you want to clear
    the selection and re-select again, just click “Reset”.

    Click <Apply> at the bottom of the screen to save the above configurations



  • Page 41

    Schedule
    Schedules can be created for use with enforcing rules. For example, if you
    want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a
    schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of
    3pm and End Time of 8pm.

    Click <Apply> at the bottom of the screen to save the above configurations



  • Page 42

    13

    Advanced Settings

    Network Address Translation (NAT) allows multiple users at your local site to
    access the Internet through a single Public IP Address or multiple Public IP
    Addresses. NAT provides Firewall protection from hacker attacks and has the
    flexibility to allow you to map Private IP Addresses to Public IP Addresses for
    key services such as Websites and FTP. Select Disable to disable the NAT
    function.



  • Page 43

    Port Forwarding

    Multiple connections are required by some applications, such as internet
    games, video conferencing, Internet telephony, and others. These
    applications have difficulties working through NAT (Network Address
    Translation). This section is used to open multiple ports or a range of ports in
    your router and redirect data through those ports to a single PC on your
    network.

    Enable Port Forwarding Enable Port Forwarding.

    Local IP This is the LAN client/host IP address that the Public Port number
    packet will be sent to.

    Port Range This is the port range that has to be opened for your application
    (for the above Local IP host).

    Type Select the port number protocol type (TCP, UDP or both). If you are
    unsure, then leave it to the default “both” setting. Public Port Enter the
    service (service/Internet application) port number from the Internet that will
    be re-directed to the above Private IP address host in your LAN



  • Page 44

    Comment The description of this setting.

    Add Virtual Server Fill in the "Private IP", "Private Port", "Type", “Public
    Port” and "Comment" of the setting to be added and then click "Add". Then
    this Virtual Server setting will be added into the "Current Virtual Server Table"
    below.

    Remove Virtual Server If you want to remove Virtual Server settings from
    the "Current Virtual Server Table", select the Virtual Server settings you want
    to remove in the table and then click "Delete Selected". If you want to
    remove all Virtual Server settings from the table, just click the "Delete All"
    button. Click "Reset" will clear your current selections.
    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 45

    Virtual server
    Use the Virtual Server function when you want different servers/clients in
    your LAN to handle different service/Internet application type (e.g. Email,
    FTP, Web server etc.) from the Internet. Computers use numbers called port
    numbers to recognize a particular service/Internet application type. The
    Virtual Server allows you to re-direct a particular service port number (from
    the Internet/WAN Port) to a particular LAN private IP address and its service
    port number.

    Enable Virtual Server Enable Virtual Server.

    Local IP This is the LAN client/host IP address that the Public Port number
    packet will be sent to.

    Local Port This is the port number (of the above Local IP host) that the
    below Public Port number will be changed to when the packet enters your
    LAN (to the LAN Server/Client IP)

    Type Select the port number protocol type (TCP, UDP or both). If you are
    unsure, then leave it to the default “both” setting. Public Port Enter the



  • Page 46

    service (service/Internet application) port number from the Internet that will
    be re-directed to the above Private IP address host in your LAN

    Comment The description of this setting.

    Add Virtual Server Fill in the "Private IP", "Private Port", "Type", “Public
    Port” and "Comment" of the setting to be added and then click "Add". Then
    this Virtual Server setting will be added into the "Current Virtual Server Table"
    below.

    Remove Virtual Server If you want to remove Virtual Server settings from
    the "Current Virtual Server Table", select the Virtual Server settings you want
    to remove in the table and then click "Delete Selected". If you want to
    remove all Virtual Server settings from the table, just click the "Delete All"
    button. Click "Reset" will clear your current selections.
    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 47

    Special application
    Some applications require multiple connections, such as Internet games,
    video Conferencing, Internet telephony and others. In this section you can
    configure the router to support multiple connections for these types of
    applications.

    Enable Trigger Port Enable the Special Application function.

    Trigger Port This is the out going (Outbound) range of port numbers for this
    particular application.

    Trigger Type Select whether the outbound port protocol is “TCP”, “UDP” or
    both.

    Public Port Enter the In-coming (Inbound) port or port range for this type of
    application (e.g. 2300-2400, 47624)

    Public Type Select the Inbound port protocol type: “TCP”, “UDP” or both
    Comment The description of this setting.



  • Page 48

    Popular applications This section lists the more popular applications that
    require

    multiple

    connections.

    Select

    an

    application

    from

    the

    Popular

    Applications selection. Once you have selected an application, select a
    location (1-10) in the Copy to selection box and then click the Copy to button.
    This will automatically list the Public Ports required for this popular application
    in the location (1-10) you specified.

    Add Special Application Fill in the "Trigger Port", "Trigger Type”, “Public
    Port”, "Public Type", "Public Port" and "Comment" of the setting to be added
    and then click "Add". The Special Application setting will be added into the
    "Current Trigger-Port Table" below. If you happen to make a mistake, just
    click "Clear" and the fields will be cleared.

    Remove If you want to remove Special Application settings from the "Current
    Trigger-Port Table", select the Special Application settings you want to remove
    in the table and then click "Delete Selected". If you want remove all Special
    Application settings from the table, just click the "Delete All" button. Click
    "Reset" will clear your current selections.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 49

    Application Layer Gateway
    You can select applications that need “Application Layer Gateway” support.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 50

    UPNP
    With UPnP, all PCs in you Intranet will discover this router automatically. So,
    you don’t have to configure your PC and it can easily access the Internet
    through this router.

    UPnP Feature You can enable or Disable the UPnP feature here. After you
    enable the UPnP feature, all client systems that support UPnP, like Windows
    XP, can discover this router automatically and access the Internet through this
    router without having to configure anything. The NAT Traversal function
    provided by UPnP can let applications that support UPnP connect to the
    internet without having to configure the virtual server sections.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 51

    QoS
    QoS can let you classify Internet application traffic by source/destination IP
    address and port number. You can assign priority for each type of application
    and reserve bandwidth for it. The packets of applications with higher priority
    will always go first. Lower priority applications will get bandwidth after higher
    priority applications get enough bandwidth. This can let you have a better
    experience in using critical real time services like Internet phone, video
    conference …etc. All the applications not specified by you are classified as rule
    name “Others”. The rule with a smaller priority number has a higher priority;
    the rule with a larger priority number has a lower priority. You can adjust the
    priority of the rules by moving them up or down.

    Enable/Disable

    QoS

    You

    can

    check

    “Enable

    QoS”

    to

    enable

    QoS

    functionality for the WAN port.

    Traffic mapping Click “Add traffic class” then enter a form of the QoS rule.
    Click “Apply” after filling out the form the rule will be added into the table.



  • Page 52

    Edit a QoS rule Select the rule you want to edit and click “Edit”, then enter
    the detail form of the QoS rule. Click “Apply” after editing the form and the
    rule will be saved.

    Adjust QoS rule priority You can select the rule and click “Move Up” to
    make its priority higher. You also can select the rule and click “Move Down” to
    make its priority lower.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 53

    Mode
    The mode-function allows you to configure the Modem-router as a pure
    modem, without router functionality.

    Note that this feature only works for DHCP and PPPoE internet connections.

    Click <Apply> at the bottom of the screen to save the above configuration.



  • Page 54

    14

    TOOLBOX Settings

    Password change options
    You can change the password required to log into the broadband router's
    system web-based management. By default, the password is: admin.
    Passwords can contain 0 to 12 alphanumeric characters, and are case
    sensitive.

    Current Password Fill in the current password to allow changing to a new
    password.

    New Password Enter your new password

    Confirmed Password Enter your new password again for verification
    purposes

    Click <Apply> at the bottom of the screen to save the above configurations



  • Page 55

    Time Zone
    The Time Zone allows your router to base its time on the settings configured
    here, which will affect functions such as Log entries and Firewall settings.

    Set Time Zone Select the time zone of the country you are currently in. The
    router will set its time based on your selection.

    Time Server Address You can set an NTP server address.

    Enable Daylight Savings The router can also take Daylight savings into
    account. If you wish to use this function, you must check/tick the enable box
    to enable your daylight saving configuration (below).

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 56

    Remote Management
    The remote management function allows you to designate a host in the
    Internet the ability to configure the Broadband router from a remote site.
    Enter the designated host IP Address in the Host IP Address field.

    Host Address This is the IP address of the host in the Internet that will have
    management/configuration access to the Broadband router from a remote
    site. If the Host Address is left 0.0.0.0 this means anyone can access the
    router’s web-based configuration from a remote location, providing they know
    the password.

    Port The port number of the remote management web interface.

    Enabled Select “Enabled” to enable the remote management function.

    Click <Apply> at the bottom of the screen to save the above configurations.



  • Page 57

    Firmware Upgrade
    This page allows you to upgrade the router’s firmware.

    Firmware Upgrade This tool allows you to upgrade the Broadband router’s
    system firmware. To upgrade the firmware of your Broadband router, you
    need to download the firmware file to your local hard disk, and enter that file
    name and path in the appropriate field on this page. You can also use the
    Browse button to find the firmware file on your PC.

    Once you’ve selected the new firmware file, click <Apply> at the bottom of
    the screen to start the upgrade process



  • Page 58

    Backup Settings
    The Backup screen allows you to save (Backup) the router’s current
    configuration settings. When you save the configuration setting (Backup) you
    can re-load the saved configuration into the router through the Restore
    selection. If extreme problems occur you can use the Restore to Factory
    Defaults selection, this will set all configurations to its original default settings
    (e.g. when you first purchased the router).

    Use the "Backup" tool to save the Broadband router current configuration to a
    file named "routercfg.cfg" on your PC. You can then use the "Restore" tool
    to restore the saved configuration to the Broadband router. Alternatively, you
    can use the "Restore to Factory Defaults" tool to force the Broadband router
    to perform a power reset and restore the original factory settings.



  • Page 59

    Reset
    You can reset the router’s system should any problem exist. The reset
    function essentially re-boots your router’s system.



  • Page 60

    DDNS
    DDNS allows you to map the static domain name to a dynamic IP address.
    You must get an account, password and your static domain name from the
    DDNS service providers. This router supports DynDNS, TZO and other
    common DDNS service providers.

    Enable/Disable Enable or disable the DDNS function of this router
    Provider Select a DDNS service provider
    Domain name Fill in your static domain name that uses DDNS
    Account/E-mail The account that your DDNS service provider assigned to
    you
    Password/Key The password you set for the DDNS service account above

    Click <Apply> at the bottom of the screen to save the above configurations.






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sitecom WL-363 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Sitecom WL-363 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 5,59 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info