Skandia Digital Multimeter 1088024
This multimeter has been designed according to IEC-61010
concerning electronic measuring instruments with an overvoltage
category (CA
Only to use for measurements in a 1-phase electrical 600V
installation after the group distribution frame.!!!
Also to use for measurements of electric appliances with a plug
and lighting connected on this installation after the group
distribution frame.!!!
maximum 600V
meter is used safely and is kept in good ope g condition.
test leads supplied. If necessary
type specified in this manual.
Important safety information, refer to the operating manual.
Dangerous voltage may be pr
Earth ground.
Double insulation (Protection class II).
Over voltage category II for measurments on electric and
electronic appliances who by way of a plug is provided of
voltage. This catagory enclosed also all smaller catagory’
instance CA
when a higher degree of reliabilty
and availability is desired.
Before opening the case, always disconnect test leads from
all energized circuits
the specified voltage and current ratings:
fastened completely
T
specifications for each range of measurement.
unused terminals.
60V above earth ground in category III installations.
set the range selector at the highest position.
disconnect test leads from the circuit under test.
circuits always remember that ther
voltages pulses at test points, which can damage the meter
30V AC rms. Keep fingers behind the probe barriers while
measuring.
Continuity T
1. Display
2.
again, just push this button once.
This switch is used to select functions and desired ranges as well
4. Hold
Plug in connector for red test lead for 10A measurement.
6. “COM”
Plug in connector for black (negative) test lead.
ΩmA” jack
Plug in connector for red (positive) test lead for voltage,
resistance and current (except 10A) measur
Accuracy is specified for a period of one year after calibration and
Maximum voltage between : CA
terminals and earth ground
converter
Overrange Indication : Only figure “1” on the display
Polarity indication :“-”displayed for negative polarity
Operating Environment :0 to 40°C
“appears on the display
600V 1V ±0.8% of rdg ± 2 digits
rms. AC for other ranges.
20μA 0.01μA ±1% of rdg ± 2 digits
2mA 1μA ±1% of rdg ± 2 digits
20mA 10μA ±1% of rdg ± 2 digits
10A 10mA ±3% of rdg ± 2 digits
200V 100mV ±1.2 % of rdg ± 10 digits
600V 1V ±1.2 % of rdg ± 10 digits
Overload Protection: 600V DC or rms. AC for all ranges.
calibrated in rms. of a sine wave.
Ω),
built-in buzzer will sound.
the diode.
DC or rms. AC.
200Ω 0.1 Ω ±0.8% of rdg ± 3 digits
2kΩ 1 Ω ±0.8% of rdg ± 2 digits
20kΩ 10 Ω ±0.8% of rdg ± 2 digits
200kΩ 100 Ω ±0.8% of rdg ± 2 digits
2MΩ 1k Ω ±1.0% of rdg ± 2 digits
Maximum Open Circuit V
DC or rms. AC for all ranges
1. Connect the red test lead to the “VΩ .mA” jack and the black
lead to the “COM” jack.
measured is not known beforehand, set range switch at the
highest range position and then reduce it until satisfactory
resolution is obtained.
3.
the red lead connection
1. Ω .mA” jack and the black
and 10A, remove red lead to“10A” jack.)
3.
connect test leads in series with the circuit.
lead connection.
1. Ω . mA” jack and the black test
lead to the “COM” jack.
3.
1. Ω . mA” jack and black test lead
to the “COM” jack. (The polarity of red lead is positive “+”.)
Ω” range position.
2.
4.
power and discharge all capacitors before applying test probes.
1. Ω .mA” jack and the black test
lead to the “COM” jack. (The polarity of red lead is positive “+”.).
position.
3.
and the black test lead to the cathode of the diode.
4.
If the connection is reversed only figure “1” will be shown.
1. Ω .mA”, black test lead to “COM”.
” position.
3.
If continuity exists, built-in buzzer will sound.
If “
”appears on display
replaced.
operator’
replace with a new one.
Be careful to observe battery polarity
Before attempting to open the case, always be sure that test leads
have been disconnected from measurement cir
tighten screws completely before using the meter to avoid electrical
shock hazard.
Skandia
©
