Bedienungsanleitung Skil 0795 (Seite 7 von 96) (Alle Sprachen)

591141

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

DURING USE

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Operate the tool at a walking pace only (do not run)

• Keep proper footing on slopes

• Always ensure that the ventilation openings are kept clear

of debris

• Take a secure stance when working (do not overreach,

especially when using steps or a ladder)

EXPLANATIONOFSYMBOLSONTOOL

3Readtheinstructionmanualbeforeuse

4Wearprotectiveglassesandhearingprotection

5Donotexposetooltorain

6Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

7 Switch o and disconnect plug before cleaning/

maintenance or if (extension) cord is damaged or

entangled

8 Double insulation (no earth wire required)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly instructions 9

- ensure that tubes A and B, collection bag C and guide

handle D are assembled correctly and that shoulder

strap E is adjusted correctly before operating the tool

! firmlytightenallscrews,boltsandnuts

• Cord restraint 0

- hook the loop in the extension cord over restraint F as

illustrated

- pull tight to secure the extension cord

• On/o !

- switch on tool by pressing trigger switch G

- switch o tool by releasing trigger switch G

! beforeswitchingonthetool,ensurethatitisnot

incontactwithanyobject

! afterswitchingoffthetoolthemotorcontinuesto

runforafewseconds

• Blowing @

- select blowing mode with switch H as illustrated (only

whentoolisswitchedoff)

- with wheel J the maximum speed can be adjusted

from low to high (1-7) (0795)

• Vacuuming/shredding #

- ensure that collection bag C 2 is attached to the tool

(for mounting see 2)

- select vacuuming mode with switch H as illustrated

(onlywhentoolisswitchedoff)

- with wheel J the maximum speed can be adjusted

from low to high (1-7) (0795)

! donotvacuumsolidobjectssuchasstones,

brokenglass,piecesofmetal

- do not vacuum liquids

- do not vacuum large volumes of leaf material at one

time thus avoiding clogging of the vacuuming opening

and blocking of the shredder impeller

- the shredding intensity depends on the size of the leaf

material and its residual moisture

! whenthetoolsuddenlystops,immediatelyswitch

itoff,disconnectplugfrompowersource,and

removeanyjammedmaterialbetweenshredder

impellerandhousing

- regularly empty collection bag C 2 (the vacuum

capacity decreases considerably when the collection

bag is full)

• Holding and guiding the tool $

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)

- use supporting wheels K for easy guiding the tube

along the ground

- for optimal results keep a 5 - 10 cm distance to the

ground

• Emptying of collection bag %

! switchoffthetoolanddisconnecttheplug

- wait until the impeller comes to a standstill before

removing the collection bag from the tool

- open the zipper of the collection bag and empty it

completely

- compostic material does not belong with domestic

waste

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots L 2)

- clean the tool aftereachuse with a soft brush or a

cloth (do not use cleaning agents or solvents)

- remove the collection bag aftereachuse, turn it

inside out and brush it thoroughly

- after removing the collection bag, ensure that possible

dirt residues are removed from the released air outlet

area

• Storage ^

- securely mount storage rail R on the wall with 4 screws

(notsupplied) and horizontally leveled

- store the tool indoors in a dry and locked-up place,

out of reach of children

- do not cover the tool with plastic (plastic may cause

moisture with rust/corrosion as a result)

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolanddisconnecttheplugbefore

investigatingtheproblem

★ Tool does not operate

- no power supply -> check power supply (power cable,

circuit breakers, fuses)

- plug not connected -> connect plug

Skil 0795 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info