Bedienungsanleitung Skil 0796 (Seite 11 von 104) (Alle Sprachen)

701724

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

• Protect the (extension) cord from heat, oil and sharp

edges

• Never use the cord for carrying, pulling or unplugging the

tool

• Inspect the cord periodically and have it replaced by a

qualied person, if damaged

• Inspect the extension cord periodically and replace it, if

damaged (inadequate extension cords can be

dangerous)

• Do not use the tool if the switch does not turn it on and

o; always have a damaged switch repaired by a qualied

person

BEFORE USE

• Be familiar with the controls and the proper use of the

tool

• Check the functioning of the tool before each use and, in

case of a defect, have it repaired immediately by a

qualied person; never open the tool yourself

• Before use, thoroughly inspect the area where the

tool is to be used and remove all solid objects that

could damage the shredding mechanism when

vacuuming (such as stones, broken glass, pieces of

metal)

• When vacuuming, never use the tool without the

collection bag in place

• Regularly check the collection bag for wear or damage

• Never operate the tool with a defective guard or housing

• Replace worn of damaged parts

• Keep all nuts, bolts and screws tight to be sure that the

tool is in a safe working condition

DURING USE

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Operate the tool at a walking pace only (do not run)

• Keep proper footing on slopes

• Always ensure that the ventilation openings are kept clear

of debris

• Take a secure stance when working (do not overreach,

especially when using steps or a ladder)

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Wear protective glasses and hearing protection

5 Do not expose tool to rain

6 Pay attention to the risk of injury caused by flying

debris (keep bystanders a safe distance away from work

area)

7 Switch o and disconnect plug before cleaning/

maintenance or if (extension) cord is damaged or

entangled

8 Double insulation (no earth wire required)

9 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly instructions 0

- mount supporting wheel K as illustrated

- ensure that tubes A and B, collection bag C and guide

handle D are assembled correctly and that shoulder

strap E is adjusted correctly before operating the tool

! firmly tighten all screws, bolts and nuts

• Cord restraint !

- hook the loop in the extension cord over restraint F as

illustrated

- pull tight to secure the extension cord

• On/o @

- switch on tool by pressing trigger switch G

- switch o tool by releasing trigger switch G

! before switching on the tool, ensure that it is not

in contact with any object

! after switching off the tool the motor continues to

run for a few seconds

• Blowing #

- select blowing mode with switch H as illustrated (only

when tool is switched off)

- with wheel J the maximum speed can be adjusted

from low to high (1-7) (0796)

• Vacuuming/shredding $

- ensure that collection bag C 2 is attached to the tool

(for mounting see 2)

- select vacuuming mode with switch H as illustrated

(only when tool is switched off)

- with wheel J the maximum speed can be adjusted

from low to high (1-7) (0796)

! do not vacuum solid objects such as stones,

broken glass, pieces of metal

- do not vacuum liquids

- do not vacuum large volumes of leaf material at one

time thus avoiding clogging of the vacuuming opening

and blocking of the shredder impeller

- the shredding intensity depends on the size of the leaf

material and its residual moisture

! when the tool suddenly stops, immediately switch

it off, disconnect plug from power source, and

remove any jammed material between shredder

impeller and housing

- regularly empty collection bag C 2 (the vacuum

capacity decreases considerably when the collection

bag is full)

• Holding and guiding the tool %

! while working, always hold the tool at the

grey-coloured grip area(s)

- use supporting wheel K for easy guiding the tube

along the ground

- for optimal results keep a 5 - 10 cm distance to the

ground

• Emptying of collection bag ^

! switch off the tool and disconnect the plug

- wait until the impeller comes to a standstill before

removing the collection bag from the tool

- open the zipper of the collection bag and empty it

completely

- compostic material does not belong with domestic

waste

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0796 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info