Bedienungsanleitung Skil 3601 (Seite 5 von 64) (Englisch, Französisch, Spanisch)

758351

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite



.Wear safety goggles and a face shield if operation is dusty.

Wear ear plugs or muffs during extended periods of operation.

Small loose pieces of wood or other objects that contact the

rear of the revolving blade can be thrown back

at the operator at excessive speed. This can usually be

avoided by keeping the guard and spreader in place for all

“THRU-SAWING” operations (sawing entirely thru the work)

AND by removing all loose pieces from the table with a long

stick of wood IMMEDIATELY after they are cut off.

/ NEVER turn the saw “ON” before clearing the table of all

tools, wood scraps, etc., except the workpiece and related

feed or support devices for the operation planned.

0NEVER place your face or body in line with the cutting tool.

G NEVER place your fingers and hands in the path of the

sawblade or other cutting tool.

GNEVER reach in back of the cutting tool with either hand to

hold down or support the workpiece, remove wood scraps, or

for any other reason. Avoid awkward operations and hand

positions where sudden slip could cause fingers or hand to

move into a sawblade or other cutting tool.

GDO NOT perform any operation “FREEHAND” — always use

the fence to position and guide the work for both rip cuts and

crosscuts.

GNEVER hold onto or touch the “free end” of the workpiece or

a “free piece” that is cut off, while power is “ON” and/or the

sawblade is rotating.

G Shut “OFF” the saw and disconnect the power cord when

removing the table insert, changing the cutting tool, or making

adjustments.

GProvide adequate support to the rear and sides of the saw

table for wider or long workpieces.

G Plastic and composition (like hardboard) materials may be

cut on your saw. However, since these are usually quite hard

and slippery, the anti-kickback pawls may not stop a kick back.

Therefore, be especially attentive to following proper set-up

and cutting procedures for ripping. Do not stand, or permit

anyone else to stand, in line with a potential kickback.

2 If you stall or jam the sawblade in the workpiece, turn saw

“OFF”, remove the workpiece from the sawblade, and check

to see if the sawblade is parallel to the table slots or grooves

and if the spreader is in proper alignment with the sawblade. If

ripping at the time, check to see if rip fence is parallel with the

sawblade. Readjust as indicated.

3 NEVER gang crosscut — lining up more than one work -

piece in front of the blade (stacked vertically, or horizontally

outward on the table) and then pushing thru sawblade. The

blade could pick up one or more pieces and cause a binding

or loss of control and possible injury.

4DO NOT remove small pieces of cut-off material that may

become trapped inside the blade guard while the saw is

running. This could endanger your hands or cause a kick back.

Turn saw “OFF” and wait until blade stops.

 !)+!'$'&& &!!%

Dull, gummy or improperly sharpened or set cutting tools can

cause material to stick, jam, stall the saw, or kickback at the

operator. Minimize potential injury by proper cutting tool and

machine maintenance. NEVER ATTEMPT TO FREE A

STALLED SAWBLADE WITHOUT FIRST TURNING THE

SAW OFF.

-NEVER use grinding wheels, abrasive cut-off wheels, fric -

tion wheels (metal slitting blades) wire wheels or buffing

wheels.

.USE ONLY RECOMMENDED ACCESSORIES.

0Make sure the cutting tool rotates in the same direction as

the rotation arrow on the upper guard. Also make sure the

cutting tool, arbor collars and arbor nut are installed pro p erly.

Keep the cutting tool as low as possible for the oper ation

being performed. Keep all guards in place whenever possible.

G Do not use any blade or other cutting tool marked for an

operating speed less than 11,000 R.P.M. Never use a cutting

tool larger in diameter than the diameter for which the saw

was designed. For greatest safety and efficiency when rip ping,

use the maximum diameter blade for which the saw is

designed, since under these conditions the spreader is near -

est the blade.

1Make sure the table insert is flush or slightly below the table

surface on all sides except for rear side. NEVER oper ate the

saw unless the proper insert is installed.

%;910A?@/>1-@10.E<;C1>?-:05:3

?-C5:33>5:05:3 0>5885:3 -:0 ;@41>

/;:?@>A/@5;:-/@5B5@51? /;:@-5:? /4195/-8? 7:;C: @;

/-A?1/-:/1>.5>@40121/@?;>;@41>>1<>;0A/@5B14->9

%;911D-9<81?;2@41?1/4195/-8?->1

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and other

masonry products, and

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust masks

that are specially designed to filter out microscopic particles.

•&41>1->1-005@5;:-8?-21@E5:?@>A/@5;:?2;><->@5/A8->

;<1>-@5;:?;2@41?-C5:@41;<1>-@5:3?1/@5;:$1-0

@41>1?@;2@419-:A-82;>?-21;<1>-@5;:

%-21@E

“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed

BELOW and other safety precautions, may result in serious personal injury.

WARNING

H%(&% %&$'&! %I

WARNING

SM 2610029990 06-13_3601 6/21/13 12:16 PM Page 5

Skil 3601 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info