Bedienungsanleitung Skytec 192 channel dmx controller (Seite 5 von 27) (Deutsch, Englisch, Holländisch, Französisch)

490925

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

5.2 Sound-control

The sound-control works via the built-in microphone or the Line In socket. Connect the sound-signal from the

mixer (e.g. Master 2) with the RCA-socket on the rear panel (input sensitivity 0.1 V - 1 V).

5.3 DMX-512 connection with the projector

The wires must not come into contact with each other, otherwise

the fixtures will not work at all, or will not work properly.

Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with

the fixture or one fixture with another.

Occupation of the XLR-connection:

You can adjust the XLR polarity via the DMX POLARITY selector.

Building a serial DMX-chain:

Connect the DMX-output of the 154.092 with the DMX-input of the nearest projector. Always

connect one output with the input of the next fixture until all fixtures are connected.

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 . resistor

between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.

Projector addressing

Please note that the 154.092 assigns the DMX-starting addresses every 16 steps. You have to

address every projector to the respective starting address. Otherwise, the channel assignment will not be

correct. All projectors with the same starting address work synchronically.

Projector

Starting

address

Projector

Starting

address

Projector

Starting

address

1 1 5 65 9 129

2 17 6 81 10 145

3 33 7 97 11 161

4 49 8 113 12 177

5.4 Assign the joystick

Hold the Program-button, until the LED is lit.

Hold the Mode- and Fine-button at the same time until the Assign-LED is lit. If the Reverse-LED is lit hold the

Mode- and Fine-button once more.

Select the Pan- or Tilt-direction via the Bank Up and Bank Down-button.

Press the Tap/Display-button in order to adjust 16-channel or 8-channel mode.

Select the desired projector via the Projector Select-buttons.

Hold the Mode-button and press the Scene-button on whose channel the Pan- or Tilt-channel is located. E.g.

if the Pan-movement is on Fader 1, hold the Mode-button and press Scene-button 1.

Hold the Mode- and Fine-button at the same time in order to leave the Assign-mode.

6. OPERATION

After you connected the device to the mains, the 154.092 is ready for use.

6.1 Manual-mode

6.1.1 Call up projectors manually

In the Manual-mode (Program-LED off), you can call up the connected projectors manually and control them

via the channel faders. Please note that the adjusted settings cannot me memorized.

Select the desired projector via the respective projector select button.

Adust the desired function via the channel faders.

Page Select-button:

Via the Page Select-button, you can adjust the channel faders from CH 1-8 to CH 9-16.

Display-button:

Via the Display-button, you can switch the display of the faderway from DMX-value (0-255) to procent (0-

100).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytec 192 channel dmx controller Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info