Bedienungsanleitung Skytec 54 kanaals DMX controller (Seite 4 von 10) (Deutsch, Englisch, Holländisch, Französisch)

490938

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Programming scenes into the memory

It is possible to store 9 different programs of 50 steps (scenes) each into the memory. Shortly press

the PROJECTOR or PROGRAM button when the display does not show the four 0. Hold the

PROGRAM button down (± 2 to 3 seconds) until the figure in the PROGRAM display starts flashing

with a dot next to it which means that you can make a selection. Select the required program number

(1 to 9) via the UP/DOWN buttons. The green programming LED continues to flash indicating that the

unit is in programming mode. Then push the PROJECTOR button and choose the required light effect

via the UP/DOWN buttons. When doing this, the light effect must be connected and set to the correct

start address. Check if the projector or dimmer reacts to the controller. Set the desired effect, position

of the mirror or projected colour via the slider controls, and confirm the setting by pressing the INSERT

button. The number in the SCENE display is automatically increased by 1 and you can now program

the following scene in the same way and confirm the new setting by pressing the INSERT button. You

can set up to 50 scenes in a program. Press the PROGRAM button to exit the programming mode.

Erasing programmed data

Erasing scenes

Keep the PROGRAM button pressed until the ‘program’ display is flashing. Choose the scene display

with the SELECT button (two dots appear). Select the scene that you wish to erase via the UP/DOWN

buttons and press the DELETE button twice. Exit the programming mode by pressing the PROGRAM

button.

Erasing a program

You can erase in one go all programmed steps (scenes) of a complete program. Keep the PROGRAM

button pressed until the ‘program’ display is flashing. Select the number that you wish to erase via the

UP/DOWN buttons. Press the DELETE button, then the PROGRAM button (AL is displayed) and

again the DELETE button. A double zero (00) is displayed in the scene display. Exit the programming

mode by pressing the PROGRAM button.

Running a program

Press the PROGRAM button and select the required program number via the UP/DOWN buttons. The

set scenes are now played automatically in sequence. Set the slider control (1) to zero and set the

speed with the slider control (2). The slider control (1) has only a function when several light effect

projectors are connected and some of these units are coupled in the SET UP.

Manual operation during an automatic program run

It is possible to switch a unit to manual mode during the running of a program. Press the PROJECTOR

button and select the unit via the UP/DOWN buttons. When you move one of the slide controls, the

selected unit leaves the automatic run and you can control the settings via the slider controls. Push the

PROJECTOR button twice to switch the manual mode off.

Technical specifications

Power supply..........................................................................................9Vdc /500mA

DMX output ................................................................................ 3-pin XLR connector

Number of channels................................................................................................ 54

DMX start addresses ........................9, pre-set to 1, 7, 13, 19, 25, 31, 37, 43 and 49

Number of programs.......................................................9 of 50 steps each (scenes)

Dimensions (hxwxd)...........................................................................7 x 30.5 x 16cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytec 54 kanaals DMX controller Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info