Bedienungsanleitung Skytec SP Hi-End Active Speaker With Bluetooth 170.318 (Seite 4 von 14) (Deutsch, Englisch, Holländisch, Spanisch)

506117

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

4 - 14

MP3 PANEL

A. DISPLAY

Shows MP3 information

B. STOP

Track stop playing

C. PLAY/PAUSE

Track play or pause mode

D. PREV

Play previous track

E. NEXT

Play next track

F. USB/SD/BLUETOOTH SWITCH

Use switch for playing from USB stick or SD card or bluetooth

G. USB CONNECTION

For connection of a USB stick with MP3 files

H. SD CARD CONNECTION

For connection of a SD CARD with MP3 files

How to connect with your Bluetooth device:

First turn on speaker, then press on “MODE” (F) till you see “AUX”. Then use

your mobile or computer to search a Bluetooth device. When you find the

“SKYTEC PLAYER” then connect. The password is: 0000

INPUT PANEL

1. Input connector for microphones

2. Volume control for the microphone

3. Volume control for the line input

4. Volume control for the output

5. Tone control for the output

6. Output connector to a second box or amplifier (line level)

7. Line input connector for the audio input source e.g. mixer, CD player,

etc.

TROUBLESHOOTING

One certain method of determining if a speaker is faulty is to substitute a speaker that is known to work correctly for the

suspected problem speaker. If the “normally correct speaker” is experiencing the same difficulties or problems as the

suspected problem speaker, use the information below to isolate the problem.

Possible cause Action

No output

Cables Reseat all connectors

Substitute known good cables

Check solder joins

Inspect cable for damage

Inspect wire or connector for stray strand that may short

Intermittent

Poor connections While it is possible for a faulty speaker to exhibit intermittent output, it’s more likely that an

output cable/connector is the problem. Check the soldering on your connectors.

Constant noise, buzzing and/or humming

Faulty electronic Any constant noise originates in the amplifier, mixer, signal processing, source device in the signal

devices, or line-level wiring. Check and correct system grounding as required. chain

check for noisy sources or electronic components. Check wiring for shielding.

Poor low-frequency output

Improper polarity When two speakers in close proximity to each other are connected out-of-polarity, they can

partially cancel each other out, especially at low frequencies. Check your speaker cables to be

sure they are all identically wired and connected. Check the balanced line signal cables to be

sure they are all correctly wired.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This

would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use

or disrespect of the warnings contained in this manual. Tronios cannot be held responsible for personal injuries caused by a

disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytec SP Hi-End Active Speaker With Bluetooth 170.318 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info