Bedienungsanleitung Smeg se 2842id2 (Seite 17 von 17) (Englisch)

335587

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Instructions for assembly

Electrical connection

• The electrical connection must be carried out by a

qualified electrician who is authorised to carry out such

work!

• Statutory regulations and the connection specifications issued

by the local power supply company must be strictly observed.

• When connecting the appliance it must be ensured that there

is a device which makes it possible to disconnect it from the

mains at all poles with a contact opening width of at least

3mm. Line-protecting switches, fuses or contactors are

suitable cut-out devices.

• When connecting and repairing the appliance disconnect it

from the electricity supply with one of these devices.

• The earth wire must be sufficiently long so that if the strain

relief fails, the live wires of the connecting cable are subjected

to tension before the earth wire.

• Any superfluous cable must be removed from the installation

area beneath the appliance.

• Make sure that the local mains voltage is the same as the

voltage on the rating label.

• To connect the appliance, unscrew the switchbox cover on the

underside of the appliance to access the terminal block. After

connecting the appliance, replace the cover and secure the

connection cable with the strain relief clamp.

• The connection cable must be at least H05 RR-F.

• If the excess cable of this appliance is damaged, it has to be

replaced by the manufacturer, the Customer service of the

manufacturer or by another qualified person to avoid danger.

• Full protection against accidental contact must be ensured on

installation.

• Attention! Incorrect connection may result in the power

electronics unit being destroyed.

Power supply

Mains voltage: 400-415V 2N~, 50-60 Hz

Component rated voltage: 230 - 240V

Electrical connections

Technical data

* Power when the power boost function is activated

Start of operation

Once the hob has been installed and the power supply has been

provided (mains connected) an automatic test of the controls will

be carried out and information for customer service will be

indicated.

Briefly wipe over the surface of the hob with a sponge and soapy

water and then dry with a clean cloth.

Dimensions

Hob Height/ Width/ Depth mm 50 x 600 x 510

Cooking zones

Back left Ø cm / kW

Front left Ø cm / kW

Front right Ø cm / kW

Back right Ø cm / kW

18/ 1.85 (2.5)*

21/ 2.3 (3.2)*

14.5/ 1.4 (1.8)*

18/ 1.85 (2.5)*

Hob, total kW 7.4

Dimensions

Hob Height/ Width/ Depth mm 50 x 600 x 510

Cooking zones

Back left Ø cm / kW

Front left Ø cm / kW

Right Ø cm / kW

14.5/ 1.4 (1.8)*

21/ 2.3 (3.2)*

26/ 2.4 (3.2)*

Hob, total kW 6.9

Dimensions

Hob Height/ Width/ Depth mm 50 x 750 x 510

Cooking zones

Back left Ø cm / kW

Front left Ø cm / kW

Front right Ø cm / kW

Back right Ø cm / kW

14.5/ 1.4 (1.8)*

26/ 2.4 (3.2)*

18/ 1.85 (2.5)*

Hob, total kW 7.4

Dimensions

Hob Height/ Width/ Depth mm 50 x 600 x 510

Cooking zones

Back left Ø cm / kW

Front left Ø cm / kW

Front right Ø cm / kW

Back right Ø cm / kW

14.5/ 1.2

21/ 2.3 (3.2)*

14.5/ 1.4 (1.8)*

18 or 12/ 1.7 or 0.7

Hob, total kW 6.6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smeg se 2842id2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smeg se 2842id2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info