655956
49
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
Safety provisions
ENGLISH 9
x The power tool must not be assembled, maintained, repaired or stored in the vicinity of open flames.
x Before assembly, cleaning, maintenance and repair, always turn off the engine and the cut-off wheel
must have stopped.
Only the idle speed setting must be performed with the engine running.
x Wear protective gloves for any work.
x The power tool requires regular maintenance. Only perform such maintenance and repair work on your
own that are described in these operating instructions and that you consider yourself skilled at
performing. Any other work must only be performed by specialist workshops authorised by us.
x Danger of burns! Do not touch the muffler while it is still hot – not even for maintenance or to check it for
tight fit.
x Only perform repairs with original spare parts.
x Danger of accident and injury! Never modify the power tool, as this may impair safety!
Before start-up, check the entire power tool for operationally safe conditions. In addition to the notes in the
operating and maintenance notes (Î chap. 8, page 29), check the following items:
x One-touch stop button must be easy to operate.
x The throttle control must move freely and return automatically to the idle position. It must not be possible
to operate the throttle control without pushing (unlocking) the throttle control lock (throttle control
locked).
x The cut-off wheel must be attached firmly to the spindle.
x Danger of fire! Ignition cable and spark plug connector must be firmly in place. Loose connection can
result in sparks which could ignite any escaping fuel/air mixture!
x In case of irregularities, visible damage, improper settings or limited function, the power tool must not be
started. In such cases, have the power tool inspected by specialist workshops authorised by us.
x Only use the power tool if it is in completely assembled condition.
x Keep at least 3 metres [approx. 10 feet] distance from the fuelling site when starting.
Never start the power tool in closed rooms.
x Hold the tool securely and firmly when starting.
Always start up on level ground and securely hold the power tool.
x Perform the starting process as described in chap. 6 on page 24.
x Check the idle setting after starting. The cut-off wheel must not rotate in idle mode.
3.6 During assembly, cleaning, maintenance and repair
3.7 Before start-up
3.8 When starting
49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Solo 879-12 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info