Bedienungsanleitung Solo 879-12 (Seite 57 von 160) (Deutsch, Englisch, Französisch, Spanisch)

655956

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Preparing for use

ENGLISH 17

x Push on outer mounting flange (c) so that the curved side points southwards, i.e. away from the cut-off

wheel.

x Push on wheel (b) and turn in cut-off wheel attachment screw (11).

x Insert blocking pin (a) entirely into the blocking opening (12) and firmly tighten (30 Nm [22.1 ft·lbf]) the

cut-off wheel attachment screw (11).

Securely hold the power tool at the top handle with one hand and push it firmly onto the ground.

x Remove the blocking pin (a).

The power tool's spindle is designed for cut-off wheels with an inner bore of 20 mm.

For proper installation of cut-off wheels with a 1" inner bore, the spindle adapter disk is required that

is included with the delivery of the power tool.

The spindle adapter disk ensures correct fit of the 1" cut-off wheel on the spindle.

x Installation of cut-off wheels with 1" inner bore

takes place according to chap. 5.1 as of page 16.

x After applying the cut-off wheel on the spindle,

however, the spindle adapter disk (e) must be

put on the spindle (f) additionally.

x Put the spindle adapter disk (e) onto the spindle

so that it inserts between spindle and inner bore

of the cut-off wheel.

The support area of the spindle adapter disk

must point outwards in the installed condition,

i.e. away from the spindle.

The correct orientation of the spindle adapter

disk is mandatory to directly connect the plane

inner area to of the outer mounting flange to the

cut-off wheel. Only this warrants secure

attachment of the cut-off wheel.

x Application of the outer mounting flange and all

following steps must be performed again

according to chap. 5.1.

x For cut-off wheel removal, the power tool must be put securely on the ground. Securely hold the power

tool at the top handle with the left hand and push it firmly onto the ground. Î Chap. 5.4, page 18

x Insert blocking pin (a) entirely into the cut-off wheel blocking opening (12) to block the spindle.

Unscrew cut-off wheel attachment screw (11).

Remove wheel (b) and outer mounting flange (c) (also see chap. 5.1).

x Remove cut-off wheel from the spindle. For cut-off wheels with a 1" inner bore, the spindle adapter disk

also must be removed from the spindle.

x Put the outer mounting flange back onto the spindle so that the curved side points outward.

x Put on wheel (b) and turn in the cut-off wheel attachment screw (11) again. Î Chap. 5.1.

x Insert blocking pin (a) entirely into the blocking opening (12) and firmly tighten (30 Nm [22.1 ft·lbf]) the

cut-off wheel attachment screw (11) again.

Securely hold the power tool at the top handle with one hand and push it firmly onto the ground.

x Remove the blocking pin (a).

5.2 Installing cut-off wheels with 1" inner bore

5.3 Removing the cut-off wheel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 879-12 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info