655956
62
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
Preparing for use
ENGLISH 22
Loosen and turn assembly flange (j)
x Put the wheel guard on a level surface with the
assembly flange (j) pointing up (screws (g) of the
assembly flange point up).
x Turn out screw (k).
Hold the nut below the assembly flange with flat
pliers.
x Twist the assembly flange against the wheel
guard so that the receptacle bore for the
screw (k) is located between the centre stop and
the right stop (m) on the wheel guard. The
assembly flange is hard to twist. Securely hold
the wheel guard when twisting.
Limit wheel guard rotating angle with screw (k)
x Turn in screw (k) again.
For this, guide the nut (n) below the assembly
flange with flat pliers and hold it when turning in
the screw.
Turning of the wheel guard is limited by the
stops on the wheel guard between which the nut
can be moved.
Install cutting device in the outer position
x Put the cutting device on the cutting device
carrier in the outer position. For this, guide both
screws (g) of the assembly flange through the
oblong holes and put the ribbed belt support (i)
into the ribbed belt.
x Check that the ribbed belt is running freely.
Correct placement of the ribbed belt if required.
x Put on the ribbed belt cover (14) again.
Adjust the ribbed belt tension
x Screw both attachment nuts (d) of the ribbed belt
cover onto the assembly flange screws. Only
tighten the nuts manually so that the ribbed belt
tension can still be set.
x Turn ribbed belt tension screw (13) towards the
right, e.g. clockwise, to increase the ribbed belt
tension). The correct tension is reached when
the square nut (e) is on the centre mark, i.e.
between "+" and "".
x Tighten both attachment nuts (d) firmly.
j
k
m
2
g
k
n
62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Solo 879-12 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info