Bedienungsanleitung Sonic Alert SBD375 (Seite 2 von 3) (Englisch)

568042

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

DUAL ALARM CLOCK WITH ADJUSTABLE TONE, VOLUME, AND

VIBRATOR

MODEL SBD375ss

OPERATION INSTRUCTIONS

IMPORTANT- Please read these instructions carefully before use and retain for future

reference.

Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before

connecting to mains make sure that the requirements specified on the apparatus corresponds to the

available power supply i.e. USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.

Features shown on diagrams above:

1) Dual Alarm Setting 7) Slow Min/Hour Button 13) Alarm 1 (AL1) Indicator

Switch 8) Snooze Button 14) Alarm 2 (AL2) Indicator

2) Dimmer Switch 9) Time Set Switch 15) Vibrator/Bed Shaker Input

3) Clock Display 10) Tone Control Wheel 16) AC Power Input

4) PM Indicator (12 hr. only) 11) Function Switch 17) Backup Battery Compartment

5) Alarm SET/OFF Switch 12) Volume Control Wheel

6) Fast Min/Hour Button

GENERAL DATA

Power: Consumption: USA: AC 110V / 60Hz EUROPE: AC 230V / 50 Hz.

UL listed transformer (Underwriters Laboratories)

Setting the correct time-

1) Depress “TIME SET” button (9)

As you depress the “TIME” button (9) at the same time depressing the “FAST” (6) or the “SLOW”

(7) minute/hour button to advance clock display until you have desired time.

3) Lighted dot (4) located in upper left corner o

f clock display indicates time is PM, no light indicates

time is AM.

Setting the alarm time-

1) To set alarm AL1 slide “DUAL ALARM SETTING SWITCH” (1) to AL1 position.

Depress “ALARM SET/OFF” (5) button at the same time depressing “FAST” (6) or the “SLOW”

(7) minute/hour button until you reach desired alarm setting.

NOTE: when setting the alarm time if you advance more than 24 hours the display (3) will begin to

flash and alarm will sound. To stop flashing, move “FUNCTION SWITCH” (11) up then back to

OFF position. When alarm sounds display (3) will also flash.

3) Make sure alarm time is correctly set for AM or PM (4).

Once alarm AL1 has been set, slide the “DUAL SETTING SWITCH” (1) to the AL2 position.

Follow the same steps that were taken when setting alarm AL1.

Once both AL1 and AL2 have been set, slide the “DUAL SETTING SWITCH” to the middle

position AL1+AL2 for both alarms.

You will see two dots on the right side of the LED display; AL1 (13) and AL2 (14) to show alarms

have been enabled. Lighted dots indicate which alarm is set.

Alarm-

To enable the alarm function, slide the “FUNCTION SWITCH” (11) up to the position that you

desire to wake to, you can choose “VIB” for bed shaker, “BUZZ” for sound, and “VIB/BUZZ” for

both. NOTE: whichever function you choose to wake to, will be the same function for both alarms.

Snooze Operation-

1) “SNOOZE” button (8) – press after alarm has gone off. The alarm will re-

set for an additional 9

minutes for extra sleep. You may repeat up to 54 minutes.

2) When using “SNOOZE” (8) if alarm AL1 uses snooze, it will not affect alarm AL2.

Shutting Off Alarm-

Alarm can be shut off temporary for the day or permanently shut off.

When alarm AL1 goes off, press the “ALARM SET/OFF” (5) button to turn off for the day.

2) Once both alarms go off and

the “ALARM SET/OFF” (5) button has been pressed, alarms will shut

off for the day and come back on the next day at the same time if alarm settings have not changed.

To shut the alarm off permanently, slide the “FUNCTION SWITCH” (11) down to the OFF

positi

on. Alarm will not come on until “FUNCTION SWITCH” (11) is set to “VIB/BUZZ”, “VIB”,

or “BUZZ” position.

Volume Control-

1) To adjust volume, rotate wheel located on the lower right bottom corner of the clock (12).

Tone Control-

1) To adjust “TONE CONTROL” (10)

turn the wheel on the top right corner of the clock to the

desired tone sound.

Bed Shaker / Vibrator-

1) Attach the bed shaker jack to the back of clock at “VIBRATOR INPUT” (15).

2) To turn on vibrator slide “FUNCTION SWITCH” (11) to “VIB” or “VIB/BUZZ” position.

3) Place vibrator between mattress and box spring.

Battery Backup-

1) To use battery back up, install a 9-

volt alkaline battery in back of clock located under the

“BACKUP BATTERY COMPARTMENT COVER” (17). Battery not included. NOTE: the LED

display will not sh

ow during power failure, but the clock will still be running and keeping proper

time until the power comes back.AC_9V Power Input-

1) Attach the “AC POWER INPUT” (16) to the back of AC-

9V IN next to “VIBRATOR INPUT”

(15); it is the smaller input of the two.

Clock Format Switch-

Located on the back of the clock this switch is a 3 position switch to set the correct time format for your

country. The format is necessary for the clock to keep the correct time otherwise the clock may run too

fast or too slow.

NOTE:

IMPORTANT: do not confuse “AC POWER INPUT” (16) with the “VIBRATOR INPUT” (15).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonic Alert SBD375 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sonic Alert SBD375

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info