Bedienungsanleitung Sonos IN-CEILING (Seite 3 von 5) (Englisch)

700029

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

2. The speaker’s terminals are spring-loaded. Push the top of

each terminal down to open the connector and insert the

exposed wires into the holes in the spring terminals.

The speaker’s positive spring terminal is labeled with a red dot;

the negative spring terminal is labeled with a black dot. Double

check that you connected ampliﬁer “+” to speaker “+” and

ampliﬁer “–” to speaker “–”.

3. Make sure all the Roto-Lock toggle feet are retracted so that

they are tucked within the mounting hole’s border. Insert the

speaker into the hole in the ceiling (see Figure 5). The Roto-

Lock system can accommodate a ceiling material thickness of

1-1/4” (32mm) with the toggle foot cap removed the system can

accommodate a ceiling material thickness of 1-7/8” (48mm).

4. When installing into double drywall or other thicker ceiling

materials, you may need to remove part of the two-piece

toggle feet. Use a small screwdriver to gently release the two

locking levers (see Figure 4).

5. Tighten the screws on the front of the speaker bae. The Roto-

Lock toggle feet will automatically rotate into position and

begin clamping the speaker (see Figure 6). When you notice

resistance on the screws the speaker has been

clamped successfully.

6. The micro-trim grille is held in place by several small, powerful

magnets on the speaker frame. Place the grille against the

speaker and the magnets will hold it ﬁrmly in place. When

properly installed, the grille trim should make contact with the

wall all the way around the speaker.

Figure 4: Removing the Caps from the Roto-Lock Toggle Feet

Remove

Cap

Locking Levers

Figure 5: Inserting the Speaker into the Mounting Hole

Roto-Lock Clamps

(retracted)

Figure 6: Tightening the Roto-Lock Screws

Roto-Lock Screws

IMPORTANT: ALWAYS USE LOW TORQUE SETTINGS; NEVER OVER-TIGHTEN.

NOTE: ADJUST THE TENSION OF THE ROTO-LOCK CLAMPS SO THAT THE SPEAKER FRAME IS FLAT. THIS

WILL HELP ENSURE THAT THE GRILLE CONTACTS THE CEILING ALL THE WAY AROUND THE SPEAKER

FOR A PROPER FIT.

Speaker Adjustments

Pivoting Woofer and Midrange/Tweeter

SONOS In-Ceiling speakers have a pivoting woofer and a

pivoting midrange/tweeter assembly. If you’re using the speakers

in stereo or as the front left/center/right speakers in a home

theater, pivot the drivers directly towards the listening area.

If you’re using the speakers as surround channel speakers in a

home theater, pivot the drivers towards a wall or window, away

from the listeners.

To pivot the drivers apply light pressure to the ring around the

outside edge of the woofer, midrange and tweeter cone, as

shown in Figure 7. Take care not to touch or apply pressure to the

cone itself.

Figure 7: Pivoting Tweeter Left, Pivoting Woofer Right

Unlocking Sonos Audio

Enhancements

Sonos In-Ceiling by Sonance speakers include exclusive audio

enhancements when used with a Sonos Amp. Use the free Sonos

app to unlock them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sonos IN-CEILING Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info