Bedienungsanleitung Soundcraft Signature 22 (Seite 55 von 55) (Englisch)

611469

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

16, 22, 22MTK User Manual

APPENDIX 1: NO SOUND?

NO SOUND

APPENDIX 1: NO SOUND?

A Troubleshooting Guide.

Isaninputfailingtoappearatappearingatanoutput?Thebestapproachitistorstmakesurethe

inputisvalid,andthenworkthroughthesignalpathtondoutwherethe‘break’is...Checktheexact

audio path of any signal by referring to the signal path diagrams in Chapter 4.

Check Solos

If a PFL light on an input channel is lit, or the AFL/PFL ACTIVE LED (below main audio meter) then a solo is active

and all channels except those that are ‘soloed’ will be muted. This will only affect the headphones output.

Clear all active Solos by pressing any illuminated Input Channel PFL buttons and any engaged Aux Master AFL buttons.

Check Input Channel Path To Solo Bus

The channel solo can be very useful here. If you Solo the channel it will send a post-EQ, pre-Mute signal to the Solo

bus and you should be able to see signal indicated on the main meters, or hear it in the headphones.

Things that might prevent the signal getting that far include a GAIN control set too low, phantom power not switched

on for a source that requires it (condenser microphone, active DI etc), or an active SUB RTN switch on a channel

where there is no USB input (MTK models only).

Check the Input Channel routing diagram (Section 4.1) and ensure the channel controls are set up correctly.

Check Input Channel Path To Routing

If the signal is present on the Solo bus with PFL engaged, the problem might be further down the input channel. It

could be simply that the Mute is active, or the fader is down - or there could be a problem with the routing.

For a signal to go to the Main Stereo Bus or to a Group Bus, the corresponding routing switch must be engaged

(MST,1-2,or3-4).Also,apanorbalancecontrolcanhaveasignicanteffect-ifthesignalisroutedtoGroups1-2,

for example, and the pan control is full left (Group 1), you won’t hear anything from the Group 2 bus.

Check Mute and fader status, and that the channel routing selections are correct.

Check Bus Masters

If you have routed signal to the Main Stereo bus or a Group bus, or you have turned up the channel’s contribution

to an Aux bus, then the master controls for that bus must be set correctly. For example, if the signal is routed to the

Stereo master but the Stereo Master fader is down, you won’t hear anything.

Check the controls on any Bus Masters that the signal is routed to.

No FX?

For an internal FX to be heard, there must be a source contribution from a valid input. Increase the level to the FX

bus using the Aux/FX control (Aux 4/FX for Signature 16, Aux 4/FX and Aux 5/FX for Signature 22 and 22MTK.

Also, the signal is return through the corresponding FX Return Channel. Troubleshoot this signal path as you would

do for a normal input channel.

The internal FX routing has three stages - send, processor, and return. All three must be set correctly for the FX to be heard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft Signature 22 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info