Bedienungsanleitung Stagg 500 BA115 (Seite 1 von 2) (Englisch)

644335

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

FRONT PANEL

1) INPUT - Plug your bass in here. We recommend that you always use a high-quality shielded cable to

prevent any background noise interference or unwanted feedback.

2) VOLUME - This control determines the level of the input signal going into the amplier.

3) PASSIVE/ACTIVE - When released (or off), this selector switches the INPUT of the amplier to a high

impedance (sensitivity) circuit, suitable for basses with PASSIVE electronics. When pushed in (or on), it

connects the INPUT to a low impedance (sensitivity) circuit, suitable for use with ACTIVE basses.

4) TREBLE - This control determines the level of high frequencies in the output signal. Adding TREBLE will

make your bass sound brighter and sharper.

5) MID - This control determines the level of middle frequencies in the output signal. Adding MID will

make your bass sound rounder and fuller.

6) BASS - This control determines the level of low frequencies in the output signal. Adding BASS will make

your bass sound warmer and heavier.

7) COMPRESSION - This control reduces the dynamic range of the output signal and evens out the

changes in volume that occur according to how hard you play your instrument. Adding COMPRESSION will

make your bass sound smoother and clearer.

8) MASTER - This controls the overall listening level of the amplier. Adjust it to your preferred level.

9) CD/MP3 INPUT - This is a line level 1/4" (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player

may be connected.

10) EFX SEND - This amplier is equipped with an effects loop which allows you to plug effects between

the preamp and the power amp. The EFX SEND jack is a line level 1/4" (Ø 6.3 mm) output jack into which

you may connect one or several outboard effects, eg Flanger, Delay, Chorus etc. The EFX SEND should be

connected to the input jack of the rst effect in your chain.

11) EFX RETURN - This is a line level 1/4" (Ø 6.3 mm) input jack into which you should connect the

output jack of the last effect in your chain. The effects loop may also be used with a multi-effects rack

system, or with a single effect.

12) BALANCED OUT - This front panel XLR socket drives a post E.Q, post effects, balanced output signal

for connecting directly to one of the Balanced Microphone inputs of a mixing console.

13) POWER LED - When this red LED is lit, the amplier is ready to work. When it is off, it means the

amplier is powered off.

Features and Specications are subject to change without notice.

2 3

USER MANUALUSER MANUAL

500 BAH - 500 BA115 500 BAH - 500 BA115

1 2 3 4 5 6 7 8 9 10 11 12 13

STAGG 500 BAH & STAGG 500 BA115

1 2 4 5 5 53

500 BAH 500 BA115

BACK PANEL

WARNING

This amplier must be earthed. Please check that the supply voltage details given on the rating label

(located on the rear panel) are in accordance with your electricity supply.

1 POWER SWITCH - This switch turns the amplier on or off.

2 POWER FUSE - In the event of the power fuse having to be replaced, rst unplug the power cable from

the mains outlet. Then remove the fuse cover and replace the power fuse with one of the same type and

value. Never plug the power cable back into the mains outlet without the fuse cover. When powering on

the amplier, if the power fuse blows up again, go to a suitable service centre for repair.

3 MAINS INPUT - This is the input socket into which the mains power cable must be connected. This

amplier is supplied with a power cable with a moulded-on plug. If the socket outlets in the home are

not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can handle the

power required for this amplier.

4 VOLTAGE SELECT - This switch selects the chosen voltage level between 110-120VAC and 220-

240VAC as appropriate. This switch may be accessed by unscrewing the safety cover. Always make sure

that the selected voltage level is in accordance with your electricity supply.

5 SPEAKER OUT - The 500 BAH head features two external speaker sockets to connect one (or two)

external Speaker Cabinet(s) providing the total load impedance is not lower than 8 Ohms, while the 500

BA115 combo allows you to plug one external Speaker Cabinet only with a minimum load impedance of 16

Ohms, i.e: Stagg 300 BC115 (1x 15”) and Stagg 300 BC410 (4x 10”), 300W RMS/16Ω Speaker Cabinets

for bass ampliers.

TECHNICAL SPECIFICATIONS 500 BAH EU+UK 500 BA115 EU+UK

Description 500W Bass Amp Head

500W Bass Combo

and 1x 15" Speaker

Max. Rated Power 500 Watts RMS @ 8 Ohms 500 Watts RMS @ 8 Ohms

Speakers (N * Ø/ P/ Z) 1 x 15"/ 300W/ 16 Ohms

External Speaker Out 2 x SPK 1 x SPK

Minimum Load 8 Ohms 16 Ohms

Frequency Response 40 Hz to 20 kHz 40 Hz to 20 kHz

Total Harmonic Distortion 0.5% 0.5%

Signal to Noise Ratio - 68 dB @ max Rated Power - 68 dB @ max Rated Power

Input Impedance 220k Ohms 220k Ohms

Power Consumption 900 Watts max 900 Watts max

Maximum Input Level 45 mV RMS 45 mV RMS

Maximum Gain 47 dB @ 1 kHz 47 dB @ 1 kHz

Dimensions (H x L x P) 23.5 x 73 x 38 cm 72.5 x 73.5 x 38 cm w/o casters

Dimensions (H x W x D) 9.2 x 28.7 x 15 in 28.5 x 28.9 x 12.2 in w/o casters

Weight 29.5 kg / 65.0 lb 55.3 kg/ 121.9 lb

Stagg 500 BA115 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stagg 500 BA115

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info