Bedienungsanleitung Stanley FMC795B (Seite 5 von 68) (Alle Sprachen)

721834

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH

(Original instructions)

5. Tank latch

6. Intake port

7. Battery port

8. Vacuum hose

9. Hose clip

10 . Side exhaust port

11. Crevice tool

12. Wide nozzle tool

Assembly

Attaching vacuum hose (Fig. A)

The vacuum hose (8) will need to be attached to the

vacuum before using the appliance.

u Place the vacuum on a at, rm surface.

u Unlatch tank latches (5) and remove power head from

the tank. Remove the hose (8) from the tank.

u Align the hose end (13) with the intake port (6) on the

front of the appliance, ensuring the hose alignment lock

(14) is aligned with the arrow (15) on the intake port.

u Insert the hose end into the intake port and twist

clockwise to lock in place.

u Replace power head onto the tank and secure latches.

Note: The power head will only t onto the tank when the

intake port on the front of the power head and the storage

area for the wide nozzle tool on the tank are aligned as

shown in gure A.

Charging the battery (not supplied)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell tempera-

ture is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell temperature

warms up or cools down.

u To charge the battery (16), insert it into the charger. The

battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the charg-

er.

u Plug in the charger and switch on at the mains.

The charging indicator will ash continuously (slowly).

The charge is complete when the charging indicator lights

continuously. The charger and the battery can be left connect-

ed indenitely with the LED illuminated. The LED will change

to ashing (charging) state as the charger occasionally tops

up the battery charge.

The charging indicator will be lit as long as the battery is

connected to the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator will ash red at a fast rate. Proceed as follows:

u Re-insert the battery (16).

u If the charging indicators continues ashing at a fast rate,

use a different battery to determine if the charging process

works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

service centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too cold,

the LED will alternately blink, fast and slow, one ash at each

speed and repeat.

Installing and removing the battery pack (not

supplied) (Fig. B)

Warning! Ensure battery port and terminals are dry and clean

before installing battery pack.

u To install the battery pack (16) into the power head, align

the battery pack with the rails inside the tool’s battery port

(7) until the battery pack is rmly seated in the tool and

ensure that it does not disengage.

u To remove the battery pack from the tool, press the

release button (17) and rmly pull the battery pack out of

the tool handle. Insert it into the charger as described in

the charger section of this manual.

Correct hand position

Warning! To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden reaction.

u Proper hand position requires one hand on the main

handle (2).

Use

On / Off Switch (Fig. C)

u Attach the appropriate accessory to the hose (8).

u Insert battery pack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC795B Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info