Bedienungsanleitung Stanley SLM-196-510-SP (Seite 12 von 93) (Deutsch, Englisch, Dänisch, Italienisch, Portugiesisch, Schwedisch, Norwegisch, Finnisch)

720574

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

overloaded.

• Run the equipment at walking speed in lines that are

as straight as possible.

For uninterrupted mowing, the lines should always

overlap by a few centimetres.

• Do not move backwards.

• On slopes, always work across the slope.

• If the blade comes into contact with a foreign body,

switch off the engine immediately. Wait until the blade

is stationary and check the equipment for damage.

Restart work only if the equipment is undamaged.

• Switch off the equipment during longer breaks and for

transportation and wait until the blade is stationary.

Starting and Stopping the Engine

- Check the petrol and oil levels regularly and reﬁll in

time.

- Start the equipment on a sturdy, level base, if possible

not in long grass. Ensure that the cutting tool is touching

neither objects nor the ground.

Start the Engine:

1. Pull the safety catch (3) towards the handle bar and

hold it.

2. Pull the starter cord (23) and the engine starts.

Stopping the Engine:

3. Release the safety catch (3), the engine stops and the

blade is slowed.

Mowing

1. Start the engine (see above).

2. Wheel drive on: pull the drive catch (1) towards the

handle bar. The mower moves forwards.

3. Wheel drive off: release the drive catch (1). The

equipment stops.

Setting the Cutting Height

The equipment has 8 positions for setting the cutting

height.

1. Pull the lever (18) outwards and push it to the desired

position 1-8 (Fig.11).

2. Push the lever (18) back in.

Emptying the Grass Collection Box

Through the observation window ﬁtted in the rear impact

protection ( 7), you will see when the grass collection

box is full.

1. Stop the engine and wait until the blade is stationary.

2. Lift the rear impact protection (7) and remove the

grass collection box (20).

3. Empty (see “disposal / environmental protection“

chapter) and reassemble the grass collection box (20).

Mowing with the Mulch Kit

When mulch mowing, the grass is cut, chaffed and

spread on the lawn all in one go. The cut grass serves as

a natural fertiliser.

Tips for Mulch Mowing:

• Cut the grass back by 2 cm from a grass height of 4-6

cm.

• Use sharp cutting blades.

• Do not mow wet grass.

7. Cleaning and Maintenance

Have any repair and maintenance work not

described in these instructions carried out by a

specialist workshop. Use only original replacement

parts. Risk of accidents! Carry out maintenance

and cleaning work strictly with the engine switched

off and spark plug connectors removed. Risk of

injury! Allow the equipment to cool before any

maintenance and cleaning work. Elements of the

engine are hot. Risk of burning!

Cleaning and General Maintenance Work

Tip the Equipment:

To clean the underside of the equipment, tip the

equipment backwards on the upper handle bar (2).

To prevent the equipment from tipping back,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SLM-196-510-SP Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info