Bedienungsanleitung Stanley STDH5510 (Seite 7 von 9) (Englisch)

720424

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Setting the drilling depth (ﬁg.B)

• Slacken the side handle (7) by turning the grip counter

clockwise.

• Set the depth stop (6) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

• Tighten the side handle by turning the grip clockwise.

Switching on and off

• To switch the tool on, press the variable speed switch(1).

The tool speed depends on how far you press the

switch. As a general rule, use low speeds for large

diameter drill bits and high speeds for smaller diameter

drill bits.

• For continuous operation, press the lock-on button (2)

and release the variable speed switch. This option is

available only at full speed in both forward and reverse

modes.

• To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation,

press the variable speed switch again and release it.

Maintenance

Your STANLEY power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Important

To ensure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment ( other than those listed in this

manual) should be performed by authorized service centers

or other qualiﬁed organizations, always –using identical

replacement parts inside.

Cleaning

Warning! Blow dirt and dust out the main housing

with dry air as often as dirt is seen collecting in and

around the air vents. Wear approved eye protection and

approved dust mask when performing this procedure.

Warning! Never use solvents or other harsh

chemicals for cleaning the non – metallic parts of

the tool. These chemicals may weaken the materials used in

these parts. Use a cloth dampened only with water and mild

soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Accessories

The performance of any power tool is dependent

upon the accessory used. STANLEY accessories

are engineered to high quality standards and are

designed to enhance the performance of power tool.

STANLEY offers a large selection of accessories available at

our local dealer or authorized service center at extra cost.

Caution: The use of any other accessory not

recommended for use with this tool could be hazardous.

Service Information

STANLEY offers a full network of company-owned and

authorized service locations throughout Europe. All

STANLEY Service Centers are staffed with trained

personnel to provide customers with efﬁcient and reliable

power tool service. Whether you need technical advice,

repair , or genuine factory replacement parts, contact the

STANLEY location nearest to you.

Notes

• STANLEY’s policy is one of continuous improvement to

our products and, as such , we reserve the right to

change product speciﬁcations without prior notice.

• Standard equipment and accessories may vary by

country.

• Product speciﬁcations may differ by country.

• Complete product range may not be available in all

countries. Contact your local STANLEY dealers for range

availability.

ENGLISH

(Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STDH5510 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info