Bedienungsanleitung Steinel BHG 360 Li-Ion (Seite 7 von 8) (Alle Sprachen)

593381

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Charging the battery

Only use the charging station shown under

. This is the only

charging station designed for the li-ion rechargeable battery used

in your hot air tool.

Note: The rechargeable battery is supplied partially charged. To

ensure full power output, fully charge the rechargeable battery in

the charger prior to first-time use.

The lithium-ion rechargeable battery can be recharged at any

time without shortening its lifespan. Interrupting the charge cycle

will not damage the rechargeable battery.

The li-ion rechargeable battery is protected from exhaustive dis-

charge by "Electronic Cell Protection (ECP)". When the battery is

run down, the hot air tool is shut down by protective circuitry:

Note: After the hot air tool automatically shut down, do not press

the ON/OFF switch any more. This may damage the rechargeable

battery.

To remove the rechargeable battery

■

Push the rechargeable battery towards the base of the hot air

tool while pressing the release button.

■

Pull the rechargeable battery from the hot air tool so that the

STEINEL logo becomes visible.

Removing rechargeable battery

The rechargeable battery

has two locking stages that are

designed to prevent the rechargeable battery from falling out

after accidentally pressing the rechargeable-battery release button

. While the rechargeable battery is inserted in the hot air tool,

it is held in position by a spring.

Inserting rechargeable battery

From the front, slide the charged battery

into the base of the

hot air tool. Push the rechargeable battery all the way into the

base so that the STEINEL logo is no longer visible and the

rechargeable battery is securely locked in place.

Rechargeable-battery temperature below 0 °C

and over 45 °C

The red LED indicator

lights up permanently

to signalise that the rechargeable battery is out-

side the fast-charging temperature range of 0 °C

– 45 °C. As soon as the permissible temperature

range is reached, the charger automatically

switches over to fast charge mode. If the re-

chargeable battery is outside the permissible charging tempera-

ture range, the red LED on the rechargeable battery lights up

when inserted into the charger.

Charging not possible

Any other fault affecting the charge cycle is

indicated by flashing red LED indicator

The charge cycle cannot be started and the

rechargeable battery cannot be charged.

This may be because:

– the battery contacts are soiled.

Action: Clean the contacts (e.g. by fitting and removing the

rechargeable battery several times) or, if necessary, replace

the rechargeable battery.

– The rechargeable battery is faulty because there is a break

in the wiring inside the rechargeable battery (single cells).

Action: Replace the rechargeable battery.

Operation

The tool is switched ON and OFF at the 3-stage switch on the

front of the grip. The distance from the object you are working on

depends on material and intended method of working. Always try

out airflow and temperature on a test piece first. Using the attach-

able accessory nozzles (see accessories) the flow of hot air can

be controlled with maximum precision. A small quantity of smoke

may occur the first time the tool is used. Switch the tool to the

"0" position by pressing switch

. Take care when changing

hot nozzles! When using the hot air tool in the self-resting pos-

ition, make sure it is standing on a stable, non-slip and clean

surface.

LED Capacity

3 x green permanently lit ≥ 2/3

2 x green permanently lit ≥ 1/3

1 x green permanently lit < 1/3

1 x green flashing reserve power

Battery charge indicator

The three green LED's of the rechargeable-battery charge indica-

tor

show the charging condition of the rechargeable battery

. For safety reasons, the charging condition can only be

requested when the electric power tool is idle.

Press button

to display the charging condition (also possible

with the rechargeable battery removed). The charge indicator

goes out automatically after approx. 5 seconds.

If none of the LED's light up after pressing button

, the

rechargeable battery is faulty and must be replaced.

While charging, the three green LED's on the rechargeable bat-

tery light up in succession and briefly go out. The rechargeable

battery is fully charged when the three green LED's are perma-

nently lit. The three green LED's go out again about 5 minutes

after the rechargeable battery has been fully charged.

The rechargeable battery features an NTC temperature monitor

that only allows it to be recharged within a temperature range of

between 0 °C and 45 °C. This gives the rechargeable battery a

long life.

Temperature monitoring indicator

The red LED temperature monitoring indicator

signalises that

the rechargeable battery or the electronics of the hot air tool (with

rechargeable battery fitted) are not within the optimum tempera-

ture range. In this case, the hot air tool will not work or fail to

work at full performance.

Rechargeable battery temperature monitor:

■

The red LED

permanently lights up after inserting the re-

chargeable battery into the charger: The rechargeable battery

is outside the charging temperature range of 0 °C to 45 °C

and cannot be charged.

■

The red LED

flashes on pressing button

or ON/OFF

switch

(with rechargeable battery inserted): The recharge-

able battery is outside the operating temperature range of

–10 °C to +60 °C. At a temperature of over 70 °C, the

rechargeable battery switches off until it returns to the opti-

mum temperature range.

The LED light is lit when the tool is switched on. In addition

to illuminating the area you are working on, it also serves as

a "tool ON" indicator light.

LED light

Setting 1 is the cold-air stage, delivering a temperature of

approx. 40 °C. Use the cold-air function for drying paint, cooling

workpieces or to cool the nozzle before changing an accessory

attachment.

Setting 2 without nozzle delivers a temperature of 400 °C.

A temperature of 500 °C is reached by fitting the 7 mm reduction

nozzle.

Setting the temperature

The integrated ring can be used for

hanging the tool.

Attention: max. pulling force = 150 N

Hanging hook

- 13 -- 12 -

LED indicators

and

not lit

LED indicators

and

do not light up after plugging into the

power socket. This may be because:

– The charger is not plugged in (properly).

Action: Push the plug into the power socket (all the way).

– Power socket, cord or charger are faulty.

Action: Check the mains voltage and have the charger in-

spected by a customer service centre authorised for STEINEL

power tools.

Note

■

The charger may heat up when used continuously or for

several charge cycles in uninterrupted succession. This is no

cause for concern and does not indicate a technical fault.

■

A significantly shorter operating time after charging indicates

that the rechargeable batteries are worn out and must be

replaced.

Rechargeable battery cooling (Active Air Cooling)

The fan controller integrated in the charger monitors the tempera-

ture of the rechargeable battery inserted in it. If battery tempera-

ture is above 30 °C, it is cooled by a fan to optimum charging

temperature. The fan makes a ventilating noise when switched

on.

When the fan is not running, the rechargeable battery is either

inside the optimum temperature range or the fan is faulty. In this

case, the rechargeable battery will take longer to charge.

Using the BHG 360 Li-Ion hot air tool

Steinel BHG 360 Li-Ion Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info