Bedienungsanleitung Steinel XLED home 2 XL (Seite 7 von 8) (Deutsch, Englisch)

643154

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

– 12 –

– 13 –

1� About this document

Please read carefully and keep in a safe place�

– Under copyright. Reproduction either in whole or

in part only with our consent.

– Subject to change in the interest of technical

progress.

Symbols

Hazard warning!

...

Reference to other information in the

document�

2� General safety precautions

Disconnect the power supply before

attempting any work on the unit�

• Installing these units involves work on the mains

voltage supply; installation must therefore be

carried out professionally in accordance with

the applicable national wiring regulations and

electrical operating conditions (

-VDE 0100,

-ÖVE/ÖNORM E 8001-1,

-SEV 1000)

• The light must be positioned so that it is not

expected that anybody can stare into the light

for any prolonged period from a distance of less

than 0.3 m.

• The ﬂoodlight enclosure heats up when the light

is on. Only adjust the angle of the LED panel

once it has cooled down. Do not look into the

LED light at short range or for any prolonged

period (> 5 min). You could damage your retina.

• Do not install the unit on (normally) ﬂammable

surfaces.

3� XLED home 2 / XLED home 2 XL

Proper use

– Sensor-switched ﬂoodlight suitable for wall

mounting outdoors.

– Fully swivelling LED panel and moveable sensor.

– Available as a standalone ﬂoodlight or intercon-

nected with the slave version.

Movement triggers lights, alarms and many

other devices. With the fully swivelling panel, the

ﬂoodlight can be used at home to provide perfect

illumination for lighting up property, or commercially

for lighting up business premises. In conjunction

with the opal cover, this extremely ecient technol-

ogy provides wide-area lighting.

Models

– XLED home 2

– XLED home 2 XL

Package contents (Fig� 3�1)

Sensor adjustment range (Fig� 3�2 / 3�3 / 5�6)

Product dimensions (Fig� 3�4 / 3�5)

Product components (Fig� 3�6)

A LED panel

B Enclosure

C Wall mount

D Sensor unit

E Twilight setting

F Time setting

4� Electrical installation

• Switch OFF power supply (Fig� 3�7)

Connecting the mains power supply lead

The supply lead consist of three wires:

L = phase conductor (usually black, brown or grey)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors

using a voltage tester; then disconnect from the

power supply again. Connect the phase conductor

(L) and neutral conductor (N) to the terminal block.

The protective-earth conductor can be looped

through by means of terminal (E).

Wiring diagram (Fig� 3�7)

Important:

Incorrectly wired connections will produce a short

circuit later on in the product or your fuse box. In

this case, you must identify the individual conduc-

tors once again and re-connect them.

The light source of this luminaire cannot be

replaced. If the light source needs to be replaced

(e.g. at the end of its service life), the complete

luminaire must be replaced.

5� Mounting

• Check all components for damage.

• Do not use the product if it is damaged.

• Select an appropriate mounting location, taking

the reach and motion detection into considera-

tion. (Fig� 4�1)

The most reliable motion detection is achieved

by mounting the unit to face across the direc-

tion in which people walk and by making sure no

obstacles (e.g. trees, walls etc.) interrupt the line of

sensor vision (Fig� 4�2 / 4�3).

Mounting procedure

• Switch OFF power supply. (Fig� 3�7)

• Undo retaining screws. (Fig� 4�4)

• Detach enclosure (B) from wall mount (C).

(Fig� 4�5)

• Detach plug-in terminal (male) from wall mount.

(Fig� 4�6)

• Mark drill holes. (Fig� 4�7)

• Drill holes and ﬁt wall plugs. (Fig� 4�8)

• Fit sealing plug. (Fig� 4�9)

– Power supply lead, concealed. (Fig� 4�10)

– Power supply lead, surface-mounted,

with spacers. (Fig� 4�11)

• Connect conductors. (Fig� 4�12)

• Connect plug-in terminal. (Fig� 4�13)

• Fit enclosure onto wall mount. (Fig� 4�14)

• Screw in retaining screws. (Fig� 4�15)

• Switch ON power supply. (Fig� 4�15)

• Make settings ➜ "6� Function"

6� Function

Factory settings for control dials

Twilight setting (E): 2000 lux

Time setting (F): 8 s

Twilight setting (Fig� 5�1 / E)

inﬁnitely variable

Control dial set to

= twilight operation,

approx. 2 lux

Control dial set to

= daylight operation,

approx. 2000 lux.

Note: To adjust the detection zone in daylight,

the control dial must be set to

= daylight

operation.

Time setting (Fig� 5�1 / F)

Control dial set to max = longest time, approx.

35min

Control dial set to min = shortest time, approx. 8s

Note: When setting the detection zone,

we recommend selecting the shortest time.

Reach setting/adjustment

The detection zone can be optimised to suit

requirements.

Sensor unit

– Sensor unit swivels through 180°. (Fig� 5�3)

– Sensor unit tilts through 90°. (Fig� 5�6)

Adhesive shrouds (Fig� 5�4)

The ﬁlm shroud can be used for masking out any

number of lens segments to limit reach as required.

Inadvertent triggering is ruled out or the sensor can

be targeted to watch over danger spots (Fig� 5�5).

Other information:

Floodlight adjustment range (Fig� 3�2 / 3�3 / 5�2)

7� Operation / maintenance

The unit is not suitable for burglar alarm systems

as it is not tamperproof in the manner prescribed

for such systems. Weather can aect operation of

the sensor-switched LED ﬂoodlight. Strong gusts

of wind, snow, rain and hail may cause the light

to come ON when it is not wanted because the

sensor is unable to distinguish between sudden

changes in temperature and sources of heat.

The detector lens may be cleaned with a damp

cloth if it gets dirty (do not use cleaning agents).

8� EC Declaration of Conformity

This product complies with the requirements

deﬁned in the following standards, legislation and

directives:

– Low Voltage Directive 2014/35/EU

– EMC Directive 2014/30/EU

– RoHS Directive 2011/65/EU

– WEEE 2012/19/EU

Steinel XLED home 2 XL Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Steinel XLED home 2 XL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info