Bedienungsanleitung Stiga 107M (Seite 9 von 11) (Englisch)

608619

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

5.3 Service position

1. Activate the parking brake.

2. Set the implement lifter in transport position.

3. If the deck has electrical cutting height adjust-

ment, disconnect the cable from the machine.

See fig. 15.

4. 125 Combi Pro, 107 M HD, 107 M:

Set the highest cutting height.

121 M

: Set the cutting height in the centre posi-

tion.

5. 125 Combi Pro:

Remove pins and washers. See fig. 2.

107 M HD

Remove pins and washers. See fig. 13.

107 M

: Lift up the rear section of the cutting

deck, undo the catches (12:L) and lower.

121 M:

Disconnect the rear section of the cut-

ting deck by removing the pins (7:I).

6. Remove the belt cover. See fig. 5:E, 8 and 10.

The number in the figure indicates the key

width.

7. Only 125 Combi Pro:

Remove the belt guide (5:F).

8. Grip the belt tensioner’s lever with your left

hand. Pull the lever and unhook the tensioner

from the belt with your right hand. See fig. 16.

9. Force the belt off the deck’s pulley.

10.Grip the front edge of the deck and lift up. Lift

until the deck is completely vertical and rest the

rear edge on the floor. See fig. 20.

Reset 125 Combi Pro in accordance with 3.1.

Reset 107 M HD in accordance with 3.2.

Reset 107 M in accordance with 3.3.

Reset 121 M in accordance with 3.2.

5.4 Cleaning

The underside of the deck must be cleaned after

each use.

Set the deck in washing position.

Clean the underside of the deck carefully. Use a

high-pressure washer, scraper and/or brush.

When the surfaces are completely dry and clean,

touch up the paintwork. Use durable yellow paint

intended for metal outdoors.

5.5 Wheels

125 Combi Pro is fitted with two lubricating cups

(21:M) for the vertical shafts.

107 M HD

is fitted with two lubricating cups for

the vertical shafts (21:M) and two lubricating cups

(21:N) for the wheel axles.

The grease nipples must be lubricated with univer-

sal grease after 50 hours of operation.

5.6 Replacing blades

Wear protective gloves when changing

blade(s) to avoid cutting yourself.

Check that the blades are always sharp.

This produces the best cutting results.

Always check the blade(s) after a collision. If the

blade system has been damaged, defective parts

should be replaced.

Always use genuine spare parts. Non-

genuine spare parts can entail a risk of

injury, even if they fit the machine.

The deck is equipped with blades accord-

ing to the following alternatives:

• Separate blades, screwed into place on the blade

bars. See fig. 22.

• Full blade. See fig. 23.

5.6.1 Separate blades

The blades are replaceable. When replacing, both

blades on the same blade bar must be replaced to

avoid imbalance.

Tightening torque:

Screws (22:P) - 24 Nm

Shear bolts (22:Q) - 9.8 Nm

In the event of a collision, the shear bolts (22:Q)

can break and the blades bend back. If this has hap-

pened, install genuine shear bolts and tighten as

above.

5.6.2 Full blade, fig. 23

The full blade is replaced when the edges are worn.

Install the new blade with the punched text facing

down.

Tightening torque: 24 Nm.

5.7 Synchronising, blades

The following decks have synchronised blades:

• 107 M

• 107 M HD

• 121 M

If one of the blades has struck a solid object (e.g. a

stone), the positive drive belt may mesh incorrect-

ly, endangering the synchronisation. This entails a

risk of the blades colliding with each other.

Correctly synchronised blades must be offset 90°

from each other. See fig. 24.

Always check synchronisation after a collision.

If there is any suspicion of incorrect synchronisa-

tion, contact an authorised Stiga workshop for re-

pair work to be carried out.

The blades in the 125 Combi Pro are freely rotat-

ing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga 107M Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info