608751
25
Zoom out
Zoom in
Vorherige Seite
1/138
Nächste Seite
USING THE MACHINE / MAINTENANCE AND STORAGE 9
EN
For your safety and that
of others:
After each use, disconnect the machine
from the mains and check for damage.
Correct maintenance is essential to maintain
the original efficiency and safety of the ma-
chine over time.
Keep all nuts, bolts and screws tight to be
sure the equipment is in safe working con-
dition.
Never use the machine with worn or dam-
aged parts. Damaged parts are to be re-
placed and never repaired.
Only use original spare parts. Parts that are
not of the same quality can seriously dam-
age the equipment and compromise safety.
During maintenance oper-
ations unplug the machine from the mains.
1. MOTOR COOLING
To avoid overheating and damage to the motor, al-
ways keep the cooling air vents clean and free of
sawdust and debris.
WARNING!
WARNING!
2. MAINTENANCE AND SHARPENING
OF THE BLADE
Periodically check that the
blades are not bent or damaged and that the
fixed comb on the blade is intact.
Adjustment of the distance between blades is not
necessary, as this is predetermined by the manu-
facturer.
If the blades are used correctly, following all the in-
structions provided, they will not require any main-
tenance work and will not need sharpening.
It is necessary to sharpen the blades only when the
trimming performance decreases and the branches
tend to stick together.
Any intervention on the blade
should always be conducted at a specialised Cen-
tre that has the most appropriate tools and is able
to perform the operations without compromising the
safety of the machine.
NOTE
WARNING!
8. MAINTENANCE AND STORAGE
Vertical trimming (Fig. 3)
Proceed to cut by using curved movements from
the bottom towards the top, keeping the blade as
far from the body as possible.
Horizontal trimming (Fig. 4)
The best results will be obtained with the blade
slightly inclined (5° - 10°) in the direction you are
cutting, proceed with a curved movement, slowly
and without interruptions, especially in the case of
very thick hedges.
4. LUBRICATING THE BLADES DURING
JOBS (Fig. 5)
If the trimming device overheats whilst working, it
is necessary to lubricate the internal surfaces of the
blades.
This operation must only
be performed when the blades have stopped
running and the motor is switched off.
WARNING!
4. END OF OPERATIONS
When you have finished your work:
– Switch off the motor as indicated above (Chap.
6).
Allow the motor to cool
before storing in any enclosure.
To reduce fire hazards, clean the machine
thoroughly to get rid of any remains of grass,
leaves or excess grease, never leave contain-
ers with the cut debris inside the storage area.
To increase the efficiency and working life of the
blades, clean and lubricate them carefully after
each work session.
– Use a soft cloth to clean the blades, along with
a brush to remove more difficult dirt and debris.
– Lubricate the blades with suitable, non-polluting
oil were possible.
WARNING!
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stiga SHT 700 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info