Bedienungsanleitung Stihl HSE 51 (Seite 26 von 288) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

537312

Zoom out

Zoom in

Vorherige Seite

1/288

Nächste Seite

HSE 41, HSE 51

English

– Receptacles of extension cords

must be splash-proof.

– To reduce the risk of stumbling,

position and mark the connecting

cord so that it cannot be damaged

or endanger others.

– The trigger switch on the control

handle and the front switch lever

must move freely – the trigger

switch and front switch lever must

return to the idle position when they

are released.

– Cutting blades securely mounted

and in good condition (clean, move

freely, not warped), properly

sharpened and thoroughly sprayed

with STIHL resin solvent (lubricant).

– Check cutter guard (if fitted) for

damage.

– Never attempt to modify the controls

or the safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the power tool.

To reduce the risk of personal injury,

do not operate your power tool if it is

damaged or not properly assembled.

To reduce the risk of electric shock:

– Always connect the power tool to a

properly installed wall outlet.

– Make sure the extension cord used

complies with the regulations for the

intended application.

– Check that the insulation of the

power cord, extension cord, plug

and coupling is in good condition.

Holding and Controlling the Power

Tool

Always hold the unit firmly with both

hands on the handles. Wrap your fingers

and thumbs around the handles.

Right-handers

Right hand on the control handle and left

hand on the loop handle.

Left-handers

Left hand on the control handle and right

hand on the loop handle.

Make sure you have firm and secure

footing and hold the unit so that the

cutting blades are always away from

your body.

During Operation

In case of imminent danger or in an

emergency, switch off the motor

immediately – release the trigger switch

and/or front switch lever.

Check that there are no bystanders in

the general work area.

Watch the cutting blades at all times –

do not cut areas of the hedge that you

cannot see.

Be extremely careful when cutting tall

hedges, check the other side of the

hedge before starting work.

Do not leave the machine outdoors in

the rain.

Your power tool is equipped with a

system designed to quickly stop the

cutting blades – they come to an

immediate standstill as soon as you

release the trigger switch and/or the

front switch lever.

Check this function at regular short

intervals. To reduce the risk of injury,

do not operate your power tool if the

cutting blades continue to run. Contact

your servicing dealer.

Take special care in slippery conditions

– damp, snow, ice, on slopes or uneven

ground.

278BA011 KN

278BA012 KN

The drive motor is not

waterproof. To reduce

the risk of a short cir-

cuit or electrocution,

never work with the

power tool in the rain or in

wet or very damp

locations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl HSE 51 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info