Bedienungsanleitung Stomer SAD-14x2-D (Seite 6 von 44) (Alle Sprachen)

555308

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Cordless drill/driver

INTENDED USE

• This tool is intended for drilling in wood, metal, ceramic

and plastic; tools with electronic speed control and left/right

rotation are also suitable for screwdriving and thread cut-

ting

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 Switch for on/off and speed control

2 Switch for changing direction of rotation

3 Keyless chuck

4 Ring for torque control

5 Switch for selecting mechanical speed

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

• Ensure the switch is in the off position before inserting

battery pack. Inserting the battery pack into power tools

that have the switch on invites accidents.

• Recharge only with the charger speciﬁ ed by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with another bat-

tery pack.

• Use power tools only with speciﬁ cally designated battery

packs. Use of any other battery packs may create a risk

of injury and ﬁ re.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the charger (charg-

ers with a rating of 230V or 240V can also be connected

to a 220V supply)

• In case of electrical or mechanical malfunction, imme-

diately switch off the tool or unplug charger from power

source

• SBM Group can assure ﬂ awless functioning of the tool

only when original accessories are used

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• This tool should not be used by people under the age

of 16 years

• Be careful not to drill or drive into areas where electrical

wires may be contacted

• Ensure that switch (2) is in the middle (locking) position

before making any adjustments or changing accessories

as well as when carrying or storing the tool

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Never charge battery outdoors

• Store tool/charger/battery in locations where tempera-

ture will not exceed 40° C or drop below 0° C

• Batteries will explode in ﬁ re, so do not burn battery for

any reason

• When damaged, and under extreme usage and tem-

perature conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, ﬂ ush eyes with clean water

for a minimum of 10 minutes and seek immediately medi-

cal attention

• When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc.

to prevent short-circuit

• Do not use charger when damaged; take it to one of

the ofﬁ cially registered SBM Group Service Stations for

a safety check

• Do not use battery when damaged; it should be re-

placed immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries

with the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of the charger to the earth terminal of

the plug

• If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left unat-

tended

To ensure longer service life and proper per-

formance of the battery, take the following ac-

tions when you start using new battery:

1. Use the new battery, without recharging it, till its com-

plete discharge.

2. Then charge the battery for 1 hour.

3. Repeat abovementioned actions (1 and 2) 3-5 times to

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when

carrying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please con-

tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of the

packaging materials can be recycled. Take these materi-

als to the appropriate recycling locations. Take your un-

wanted machines to your local SBM Group dealer. Here

they will be disposed of in an environmentally safe way.

NiCd batteries can be recycled. Deliver them to a disposal

site for chemical waste so that they can be recycled or dis-

posed of in an environmentally friendly manner.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SAD-14x2-D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info