654687

Sunbird Solar Solarpod Pro 1000 Seite 3

3
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
Section 4
_______
_________________________________________________________________
CHARGING
Fully charge before first use. For maximum efficiency,
charge after each use or every 2
is being stored. Failure to properly charge as listed below could damage the
unit and affect
performance. CAUTION: ONLY USE CHARGERS PROVIDED WITH THE SOLARPOD
TM
DAMAGE MAY OCCUR.
Charging Indicator - Indicates Charging Rate
1.
Five yellow
LEDs represent the charging rate when using any of the methods of charging
below.
2.
Each yellow
LED equals approximately 20% charge rate. This will help you to position a solar
panel in the best angle to the sun. If the Solarpod™ Pro 1000
is plugged into a 1
or 12V - 24VDC power source, all 5 LEDs should be illuminated.
Battery Indicator - Indicates Battery Capacity Level
1.
Five blue LEDs represents the current battery capacity.
2.
Each blue LED represents approximately 20% full.
Solar Charging (recommended Sunbird Solar 120W Solar Panel)
1.
The Solarpod™ Pro 1000 has built-
in battery protection and does not require a solar charge
controller.
2.
Place the solar panel in direct sun.
3.
Connect the solar charging cable (included) male pin tip to the DC IN port
on the
Pro 1000. Connect the MC4 (+) and (-) tips to the solar panel.
4.
Adjust the solar panel so that it is directly facing the sun.
Charging will begin immediately
the yellow charging LED indicators will illuminate.
5.
To ensure full battery charge, continue charging for 1 additional hour.
6.
To maximize battery cycle life, disconnect when Solarpod™ Pro 1000
is fully charged.
AC Wall Charging (Adapter Included)
1.
Connect the male pin tip of the AC Wall Charger into the DC IN port of the
Solarpod
and then plug the other end into an electrical outlet.
2.
The charging indicator on the AC Wall Charger
will illuminate red when charging is in process
and green when the Solarpod™ Pro 1000 has reached a full charge.
3.
The yellow charging LED indicators will also illuminate.
4.
To ensure full battery charge, continue charging for 1 additional hour after
1000 is fully charged.
5.
There is no need to disconnect AC Wall Charger when charging is complete.
Connecting Charging Lines to the Solarpod™ Pro 1000
1.
Align head tabs with DC IN socket on back of unit.
2.
Turn head clockwise until the silver lock tab is a
t top and press lock tab toward unit.
3.
To unplug charging head, follow the above steps in reverse order.
1. Align Tabs
.
2. Turn Clockwise
3. Press in Lock
_________________________________________________________________
charge after each use or every 2
months if it
unit and affect
TM
PRO 1000 OR
LEDs represent the charging rate when using any of the methods of charging
LED equals approximately 20% charge rate. This will help you to position a solar
is plugged into a 1
00V – 240VAC
in battery protection and does not require a solar charge
on the
Solarpod™
Charging will begin immediately
and
is fully charged.
Solarpod
™ Pro 1000
will illuminate red when charging is in process
To ensure full battery charge, continue charging for 1 additional hour after
Solarpod™ Pro
There is no need to disconnect AC Wall Charger when charging is complete.
t top and press lock tab toward unit.
Section 5
________________________________________________________________________
OPERATING INSTRUCTIONS
Once charged, the Solarpod™ Pro 1000
is ready to use right out of the box. No set up is required.
All outputs may be used simultaneously. Check your device’s specifications to make sure they are
compatible with the Solarpod™ Pro 1000.
ON/OFF Button - When on, the switches
surrounding LED
AC Power Button - When on, the switches
surrounding LED
USB Operation
• Turn the ON/OFF BUTTON on.
•
Plug in your device’s USB power or charging
•
A combined 5V/2A maximum output is available between the two ports (when fully
charged).
•
Disconnect and power off when not in use
AC Operation (max 1000W output)
• Press the AC power button
to activate the inverter
•
Plug in your device’s power or charging cable into the electrical
• Disconnect and turn off the
power when not in use
• CAUTION
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
THE VOLTAGE RATING OF THE
Solarpod™ Pro
• CAUTION
: Using devices rated higher than
minutes may cause the Solarpod™ Pro
1000
cooled the circuit will reset and the
Solarpod™ Pro
Advantages of a Pure Sine Wave Inverter
•
A pure sine wave inverter produces a nearly perfect sine wave output (less than 3%
total harmonic distortion) that is essentially
• Eliminates electrical
interference, overheating and noise.
•
Computer crashes and other appliance operational glitches can be avoided.
• Inductive loads such as variable-
speed motors and microwave ovens can be used,
and supports in running them quieter and cooler.
• Some appliances
and sensitive electronics will simply not work properly without
pure sine wave power.
•
Reduces audible and electrical noise in fans, fluorescent lights, magnetic circuit
breakers and electronic gears.
12V DC Operation (Max 15A output)
• Turn the ON/OFF BUTTON on.
•
Plug in your 12V device’s power or charging cable into the 12V Vehicle Socket
• Neither power button need to be on.
•
Disconnect and power off when not in use
________________________________________________________________________
is ready to use right out of the box. No set up is required.
All outputs may be used simultaneously. Check your device’s specifications to make sure they are
surrounding LED
light will turn green.
surrounding LED
light will turn red.
Plug in your device’s USB power or charging
cable.
A combined 5V/2A maximum output is available between the two ports (when fully
Disconnect and power off when not in use
.
to activate the inverter
.
Plug in your device’s power or charging cable into the electrical
AC socket.
power when not in use
.
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
Solarpod™ Pro
1000 UNIT YOU HAVE PURCHASED.
: Using devices rated higher than
900-1000W and operated for more than 10
1000
to overheat and shut down. Once it has
Solarpod™ Pro
1000 will be operational again.
A pure sine wave inverter produces a nearly perfect sine wave output (less than 3%
total harmonic distortion) that is essentially
identical to utility-supplied grid power.
interference, overheating and noise.
Computer crashes and other appliance operational glitches can be avoided.
speed motors and microwave ovens can be used,
and supports in running them quieter and cooler.
and sensitive electronics will simply not work properly without
Reduces audible and electrical noise in fans, fluorescent lights, magnetic circuit
Plug in your 12V device’s power or charging cable into the 12V Vehicle Socket
.
Disconnect and power off when not in use
.
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sunbird Solar Solarpod Pro 1000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info