Bedienungsanleitung Swan SI9020 (Seite 3 von 4) (Englisch)

664345

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

How to Use

Before rst use

Remove any stickers, protective foil or storage cover from the

soleplate.

Heat up the iron to maximum temperature and iron over a piece

of damp cloth for several minutes for the purpose of removing any

residue on the soleplate.

Note: It is normal for a slight odour to come from the unit during

therstuse.Thisisduetolightoilsusedtopreservecomponents

duringmanufacture.Theodourwilldisappearafterrstuse.

Operation

1. Press both Handle Release Buttons at the same time and put

the handle down (g 1). Connect the power cord to outlet, the

power light illuminates.

2. Press the tank lock button then take out water tank from stand.

Remove the limescale lter. Fillthe tankbut do not exceed the

MAXlevelindicationontheside(g2-6).

3.Replacethelimescalelterandslidethetankbackintotheiron

base, making sure it “clicks” into place. Check the garment label

for the required ironing temperature. Then turn the temperature

dial to your desired setting. And the heating light will be illuminated.

Tips: to prevent shiny spots, iron the reverse side of the fabric

for silk, wool and synthetic materials; and to prevent stains, avoid

using the steam functions (put Steam ON/OFF switch in OFF

position).

Once the soleplate temperature has reached the preset

temperature, the heating light will go out, press down Steam

Button. The pump will start and after a few seconds the steam

will come through. Please note when pressing the steam button

forthersttimeatthestartofthenewironingsession,directthe

iron away from garments to allow any small amounts of water from

previous ironing sessions to be ejected.

NOTE: THE PUMP MAY MAKE A NOISE FOR A FEW SECONDS

UNTIL IT IS PROPERLY PRIMED. YOU CAN PRIME THE PUMP

A LITTLE QUICKER IF YOU HOLD THE HAND UNIT BELOW

THE HEIGHT OF THE BASE - GRAVITY WILL GET THE STEAM

THROUGH QUICKER!

Tip: the interconnection cord can become quite hot after extended

use, do not touch! At any time during the ironing session, you can

place the iron on the silicone cushion or on the heel rest (and have

anicecupoftea).Note:thesteamoutputis60-90g/min

Alwayscheckrstwhetheralabelwithironinginstructionsisattachedtothearticle.

The iron heats up quicker than it cools down, therefore, you should start ironing the

articlesrequiringthelowesttemperaturesuchasthosemadeofsyntheticbres.

Ifthefabricconsistsofvariouskindsofbres,youmustalwaysselectthelowestironing

temperaturetoironthecompositionofthosebres.

Silk and other fabrics that are likely to become shiny should be ironed on the inner side.

Velvet and other textures that rapidly become shiny should be ironed in one direction

with light pressure applied. Always keep the iron moving at any given moment.

Pure woollen fabrics (100% wool) may be ironed with the iron set a steam position.

Preferably set steam button to the maximum position and use a dry cloth as a mat.

Note: when ironing woolen fabrics, shining of the fabric may occur. So it is suggested

that you should turn the article inside out and iron the reverse side.

Ironing Tips

Cleaning and Maintainance

AFTER IRONING

1.Takeoutthewatertank,removethelimescalelterandemptyallthewaterout,replacethelter

thenplacetankbackintotheironbase(g2-6).

2. With the tank empty, press down the steam surge button button a couple of times to remove any

remaining water in the interconnecting cord, then place the iron back on the base. Warning: the

soleplate is still hot, be careful!

3. Turn the temperature dial back to 0 position and unplug from the mains socket. Allow the iron to

completely cool before cleaning. Note: you can wipe the surface of unit clean with a soft cloth. Try

nottodislodgethesiliconecushionoutofit’smountingsbecauseitisdifculttotback!

Warning: do not immerse the steam iron or stand in water or other liquids.

AUTO-DESCALING FEATURE

Thereisalimescalelterinsidethetank.Theltercanabsorbinsolublecalciumionsandconvert

them to soluble natrium ions, which makes the water softer. This greatly reduces the build-up of

limescale.However,ifyoudoliveinahardwaterarea,thelifeofyourironwillincreasesignicantly

if you use bottled water.

Note: to keep the soleplate smooth, never let any metal materials rub against it.

REPLACE THE LIMESCALE FILTER EVERY 3 MONTHS OR MORE REGULARLY IF YOU LIVE

IN A HARD WATER AREA. VISIT WWW.SWAN-BRAND.CO.UK FOR SPARE FILTERS

wan

designed for life

wan

designed for life

Helpline Number: 0121 327 6889

WWW.SWAN-BRAND.CO.UK

Helpline Number:

0121 327 6889

WWW.SWAN-BRAND.CO.UK

use vertical steam for garments

SI9020N.indd 6-7 20/06/2012 09:25

Swan SI9020 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info