Bedienungsanleitung Sygonix 1326052 (Seite 4 von 8) (Deutsch, Englisch, Holländisch, Französisch)

707198

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Legal notice

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting,

also in part, is prohibited. This publication represent the technical status at the time of printing.

Connection

The IR lamp is equipped with a connection cable with two connectors on

the end:

• Round low-voltage socket: The external voltage/current supply is con-

nected to this socket. Make sure you use only a power supply unit with

a stabilised output voltage of 12 V/DC (direct current) (see also section

“Technical data” at the end of the operating instructions).

• Round low-voltage connector: Connect this connector to your surveillance

camera. The surveillance camera must run with an operating voltage of

12 V/DC.

Pay attention to the correct polarity of the connectors. The inner

contact must be Plus/+, and the outer contact must be Minus/-.

If the surveillance camera and the IR lamp are operated via the

Y-cable with a single power supply, make sure that the output cur-

rent of the power supply is sufcient both for the surveillance cam-

era and the IR lamp.

If you install and use the IR lamp in outdoor areas, the two connec-

tors have to be placed in a location that is protected from humidity

(in dry indoor areas). Otherwise, the connectors will corrode.

If the round low-voltage is not required, protect it with a piece of

heat shrink tubing, so that no short-circuit may occur and the con-

nector is protected from dirt/moisture.

In the dark, the IR LEDs are activated automatically. The IR light is not vis-

ible to the human eye. Therefore, check the image on your monitor screen

to control the illumination of the IR lamp.

Due to the different switching thresholds for the light of the IR LEDs

on the IR lamp and your surveillance camera, the IR LEDs on the IR

lamp and your surveillance camera are not enabled and disabled at

the same time.

Example: The light from the IR LEDs on the surveillance camera are

activated at dusk by 20 o’clock, whereas the IR lamp is activated a

little later or earlier. This is normal.

So wait until it is completely dark before checking the function of the

IR lamp and correcting the alignment.

Please bear in mind that at night coloured image reproduction changes into

a black and white monochrome representation on the connected monitor

screen (when the IR LEDs of your surveillance camera are activated).

Cleaning

Occasionally, clean the IR lamp from dust and dirt, especially the front

screen. Use a clean and soft cloth, moistened with water. Do not rub too

strongly because otherwise scratches can occur on the screen.

Never point the jet of water from a garden hose or a high pressure cleaner

at the IR lamp; do not use aggressive cleaning agents.

Tips and notes

• Both the surveillance camera and the IR lamp should always be installed

so that the equipment cannot be accessed without tools.

The same applies to the connection cable. Ideally, it should be laid in a

plastic or metal pipe.

• Longer cable lengths cause deterioration in the video signal of the surveil-

lance camera. In this case, use a suitable amplier.

If the cable used to supply the power is too long, the voltage will drop, and

thus the operating voltage for the camera will no longer be sufcient. This

may lead to stripes in the image or to a loss of signal. If necessary, use a

cable with a larger cross-section to reduce the voltage drop.

• Due to the Y-cable used on the IR lamp, the IR lamp can loop-in directly

between the surveillance camera and its voltage/power supply.

For this purpose, it is essential that the surveillance camera operates with

an operating voltage of 12 V/DC. The polarity of the connectors/sockets

must be as follows:

Outer contact = minus /-

Inner contact = plus/+

Observe the operating instructions of the surveillance camera or its volt-

age/power without fail.

The IR lamp requires a current of about 310mA. If the IR lamp is operated

through the power supply of your surveillance camera, it must be sized

accordingly so that it can power up both devices (surveillance camera and

IR lamp).

Disposal

The product must not be disposed of in the household waste.

Dispose of the product at the end of its serviceable life in accord-

ance with the current statutory requirements; e.g., return it to any

suitable collection point.

Technical data

Operating voltage ......................... 12 V/DC

Current consumption ................... max. 310 mA (with activated IR LEDs)

Connecting socket/plug ...............Outer diameter 5.5 mm

.........................................................Inner diameter 2.1 mm

.........................................................Inner contact = plus/+

.........................................................Outer contact = minus /-

IR LEDs ...........................................48

Wavelength of the IR LEDs ..........approx. 850 nm

IR range ..........................................max. 50 m

Angle of radiation .........................approx. 45°

Switching threshold .....................approx. 7 - 8 lux

IP protection class ........................IP65

Cable length ..................................approx. 40 cm

Ambient temperature ..................-20 °C to +50 °C

Weight ............................................ 216 g (incl. wall bracket/cable)

Dimensions (L x Ø) ........................125 x 64 mm (incl. wall bracket)

Sygonix 1326052 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info