Bedienungsanleitung Sym JET EUROX 50 (Seite 27 von 31) (Englisch)

517190

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

11. INSPECTION AND MAINTENANCE BEFORE RIDING

CHECKING AND CHANGING FUSES

Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having

the same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron wire to

replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.

y Remove the battery cover screws, and open the battery cover. Fuses are installed in the fuse box

located by the battery.

y Fuses must be firmly secured with wire connectors when replacing.

y Use only parts having the specified specification to replace electrical components such as light bulbs.

Using parts not having the specified specifications for replacement may cause the fuse to blow and

over-discharge the battery.

y Avoid spraying water directly on or around fuse box when washing the motorcycle.

y Take your scooter to your dealer for an inspection if a fuse is blown by unknown causes.

【REMOVE】【INSTALLATION】

CHECKING THE TURN SIGNAL LIGHTS AND HORN

y Turn the ignition switch key to “ON” position.

y Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights

flashes and also check if the warning buzzer sounds.

y Check turn signal light covers if they are dirty, crack, or loosen.

y Press horn button to check if it works.

CHECKING THE FRONT AND REAR LIGHTS

y Turn the ignition switch key to “ON” position, start the engine and then turn on the front light switch.

Check if front and rear lights come on.

y Check the brightness and direction of front light by projecting the light on the wall to see if it is correct.

y Check the front light cover if it is dirty, crack, or loosen.

CHECKING THE BRAKE LIGHT

y Turn the ignition switch key to “ON” position, hold the hand-braking levers for front and rear wheels.

Check if the brake lights come on.

y Check the brake light cover if it is dirty, crack, or loosen.

Wire

Fuse connectors

Fuse

Press in from above

CAUTION:

y Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation

of turn signal lights will be affected.

y Switch on the turn signal before changing lanes or marking a turn to inform others of your intent.

y After changing lanes or making a turn, switch of turn signal immediately by pressing the reset

button. This button is located in the center of the turn signal switch.

CAUTION:

y Use only SANYANG specified bulbs, do not use bulbs with different specifications to avoid

damaging electrical system, burning out bulbs, and discharging the battery.

y Do not modify or add other electrical components to your scooter. This may prevent an over load

or short circuit which may result in a fire some cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sym JET EUROX 50 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info