Bedienungsanleitung Tascam MF-P01 Portastudio (Seite 15 von 16) (Englisch)

460069

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

PORTASTUDIO MF-P01

Tracing faults in a recording setup is often a mixture

of logical deduction and patience. Very often, the

problem is caused by something simple; a cable

which hasn’t been plugged in properly, or a faulty

cable. If you discover a faulty cable, replace it with a

new one - it’s not worth hanging onto bad cables!

The MF-P01’s POWER light does not come on.

Is the PS-P2 adaptor plugged into the power supply?

Is the PS-P2 adaptor plugged into the MF-P01?

Is the POWER switch on the MF-P01 set to ON?

The tape does not move when the PLAY button is

pressed.

Is the tape properly inserted in the MF-P01?

Is the tape at the end of the tape?

Some tracks have been recorded on the tape, but

nothing can be heard when playing back.

If you’ve just put in a tape you recorded in another

session, make sure that it’s the right way round.

Make sure the LEVEL and MASTER controls are set

appropriately (not to "0").

If you can hear something through the headphones

but cannot from the speakers, check the LINE OUT

connections and make sure the ampliﬁer is set to the

correct input source.

Nothing appears on the meter indicators when a

source is played.

Is the source (microphone, guitar, etc.) switched on

and volume control turned up? If it uses batteries,

does it need new batteries?

Is the INPUT LEVEL control of the channel set

appropriately (not to "0")?

Cannot press the RECORD key.

Is the tape properly inserted in the MF-P01?

Is the tape record-protected?

The RECORD key is pressed, the tape moves, but

nothing is recorded, or the level is very low.

Is one of the REC FUNCTION switches depressed?

Check the LEVEL control for the track.

Is the INPUT LEVEL control set correctly?

Is the recording level is too low or too high?

Tape sounds are mufﬂed on playback.

The heads are dirty. Clean them (see "Cleaning the

heads").

The mixdown signal is noisy or distorted.

Is the recording level is too low?

Is the PHONES plug is connected during mixdown?

Track format:

4 tracks, 4 channels

Head conﬁguration:

1 x 4-track record/replay head (Permalloy)

1 x 4-track erase head (ferrite)

Motor type:

1 x DC motor (capstan and reel motor)

Tape speed:

1 7/8 in./sec (4.76 cm/sec)

Wow and ﬂutter:

0.25%

Fast wind time:

Approx 120 seconds (C-60 tape)

Power requirements:

USA/CANADA: 120 V AC, 60 Hz

U.K./EUROPE: 230 V AC, 50 Hz

AUSTRALIA: 240 V AC, 50 Hz

Power consumption:

7 W, via the supplied PS-P2 AC adaptor

Physical dimensions (w x h x d):

295 x 70 x 205 (mm), 12.0 x 2.8 x 8.1 (in.),

maximum height (including controls)

81 (mm), 3.2(in)

Weight (main unit):

1.1 kg (2.4 lb)

MIC/LINE input (1/4" phone jack)

Input level:

–50 dBV or higher

Input impedance:

50 k

Ω

LINE OUT (2 x RCA jacks)

Output level:

–10 dBV

Output impedance:

10 k

Ω

Specifications

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam MF-P01 Portastudio Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info