Bedienungsanleitung Team KA VT 28 (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

487066

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

5 TEAM KA VT 28 - 091218

Assembly page 5/28

Fax +32 2 359 95 50

ASSEMBLY

1. Loosen the cap (4), remove the small plastic sleeve from the driving shaft and the guard

mounting ring (6) from the motor housing (9).

2. Position the rear guard (7) firmly against the motor housing (9) making sure that it fits

correctly and fasten by turning the guard mounting ring (6) clockwise tightly.

3. Push the propeller (5) along the motor shaft (8). Fasten it firmly with the cap (4) by turning

counter clockwise.

4. Hang the front guard (2) to the rear guard (7) with the position fixer (3) provided at the

front guard rim, and then clamp together with the clips provided.

5. To ensure that it is impossible to have access to the fan propeller without using a tool, a

screw is provided with this appliance in order to attach both parts of the mesh guard

together. This screw must be tightened on the lower part of the guards. We will not be

responsible for any injuries in case this screw has not been tightened before using the

appliance.

WALL MOUNTING

Use the 3 screws and plugs that are delivered with your appliance to attach the metal

mounting bracket to the wall.

Pay attention before attaching the mounting bracket: check if the chosen position allows you

to use all functions of the fan (oscillation, tilting adjustment…).

Attach the fan to the mounting bracket on the wall by sliding the slot at the back of the

control panel over the mounting bracket.

BATTERIES

 To be able to use the remote control, you have to insert 2 batteries first. To do so:

 Open the battery compartment.

 Insert the batteries, respecting the + and - polarity. Use two batteries of type AAA of

1.5V. Never mix new batteries with used batteries nor mix batteries of different types.

 Close the compartment.

 When you decide to throw away your appliance, first remove the batteries in order to

protect the environment. Please dispose of the batteries in an environmentally

friendly way by handing them in a place intended for this end.

Attention: if the remote control will not be used for a long period of time, it is recommended to

remove the batteries because otherwise they might leak.

REMOTE CONTROL

 The remote control has to be aimed at the receiver of the fan in order to function.

 The remote control works at a distance up to 5 metres. If the remote control is not

aimed at the receiver, the working distance will be less than 5 metres.

 The remote control may not function in rooms where heavy machinery is functioning

at the same time.

 Try to avoid blocking the space between the remote control and the receiver.

 Handle the remote control with care. Do not let it fall and do not hit it against hard

objects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team KA VT 28 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info