Bedienungsanleitung Technics SB-AS100 (Seite 3 von 4) (Englisch)

536127

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

RQT5460

Operation

Set the low pass filter, volume and phase to suit characteristics of

the speaker and SB-AS100 combination.

1 Set [POWER] to the “ ON” position.

The unit is now in standby mode and the POWER indicator

turns red.

When a signal is received the unit turns ON automatically and

the indicator turns green.

The unit automatically switches to standby if a signal is not

received for approximately two (2) minutes

2 Set [LOW PASS FILTER] to a suitable

frequency. Refer to “Frequency re-

sponse by LOW PASS FILTER setting”.

3 Set [VOLUME] to a suitable level. Refer

to “Frequency response by VOLUME

setting”.

4 After playing some music, set [PHASE]

to “ NORMAL” or “ REVERSE”,

whichever position allows playback to

sound normal.

For your reference:

If subwoofer and front speaker phase are the inverse of one

another, they will tend to cancel each other out. Playback will

not be normal and sounds will seem muffled.

When settings are complete

The only operation you should have to perform daily is press

[POWER] to turn the unit ON/OFF.

If you reposition the system and the acoustics change, reset the unit

as necessary.

If the volume output is too loud, this unit's amplifier can be clipped,

causing output to sound unusual. Reduce the volume of the receiver

or amplifier or the volume of this unit if this occurs.

Frequency response by LOW PASS FILTER setting

Frequency response by VOLUME setting

Front

Rear

Note

CAUTION:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one

of the following measures:

¡Reorient or relocate the receiving antenna.

¡Increase the separation between the equipment and receiver.

¡Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

¡Consult the dealer or an experienced radio/TV technician for

help.

Any unauthorized changes or modifications to this equipment

would void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SB-AS100 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technics SB-AS100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info