Bedienungsanleitung Technics SH-MZ1200 (Seite 13 von 16) (Englisch)

536109

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

RQT7230

Fader start function

You can start music play from the SL-DZ1200 direct drive digital turntable (not included) using the channel fader and cross fader by connecting the

digital turntables to CH1 and CH4. (A control cable is necessary for this connection. page 8)

3 Switch [FADER START (CH1)] to ON

1 Turn [ASSIGN A] and select any number

other than 1

•The channel fader will not start the digital turntable if 1 is

selected.

2 Push the channel fader all the way to

zero

4 Push the channel fader up when you

want to start play

•Play instantly begins from the digital turntable.

Start using the channel fader

If you push the channel fader back to the original position (zero) after

play on the digital turntable has started, the digital turntable returns to

the set point and waits in the standby position.

3 Switch [FADER START (CH1)] to ON

1 Turn [ASSIGN A] and select 1

2 Push [CROSS FADER] all the way in the

direction opposite the source you want

to start ( )

Start using the cross fader

If you push the cross fader back to the original position after play on

the digital turntable has started, the digital turntable returns to the set

point and waits in the standby position.

4 Slide [CROSS FADER] in the direction

opposite of instruction 2 when you want

to start play

•Play instantly begins from the digital turntable.

Alternate play of two digital turntables connected to CH1

and CH4

When the cross fader operation switch is set to NORMAL.

3 Switch [FADER START (CH1)] and

[FADER START (CH4)] to ON

1 Turn [ASSIGN A] to select 1 and turn

[ASSIGN B] to select 4

4 Push [CROSS FADER] all the way in the

direction opposite of instruction 2

(towards ), when you want to start

play

•Play instantly begins from the digital turntable connected to

CH1. (At the same time, the digital turntable returns to the

set point when playing on CH4)

5 Push [CROSS FADER] all the way in the

direction opposite of instruction 4

(towards )

•Play instantly begins from digital turntable on CH4.

•Play on CH1 instantly returns to the set point.

When the digital turntable you want to control is connected to CH1

and the channel fader operation switch is set to NORMAL.

•When individually adjusting the left (L) and right (R) input ( page

12), perform the following instructions simultaneously for the CH1

and CH2 channel faders on the panel.

When the digital turntable you want to control is connected to CH1

and the cross fader operation switch is set to NORMAL.

Before use

•Turn [MODE] to TURNTABLE on the rear panel of the digital

turntables connected to CH1 and CH4.

•Set the auto cue point and cue point on the digital turntables

connected to CH1 and CH4, and standby at the set point.

Note

While you are using the fader to start play, turning the unit off and on

may stop or start the digital turntable.

2 Push [CROSS FADER] all the way in the

direction opposite the source you want

to start ( )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SH-MZ1200 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info