Bedienungsanleitung Techno line EA 3000 Anemometer (Seite 1 von 1) (Englisch)

564382

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Hand held Anemometer

Operating Manual

Introduction:

Congratulations on purchasing this pocket-sized anemometer, this innovative

product provides wind speed information for any outdoor activities. The operation of

this product is simple and straightforward and by reading this operating manual,

users will receive the optimum benefits of all its features.

The Anemometer

Features:

· Wind speed measure in mph, Km/h, m/s or Knots

· LCD back-light

· Auto power OFF

· Neck band included

· Water resistance

Setting up:

1. Firstly, use a large coin to open the battery

cover at the back of the anemometer as

indicated above.

2. Checking the correct polarization, insert

1 x 3V (CR2032) lithium cell, positive (+) pole

up into the battery compartment and replace

the cover.

3. When the battery is inserted, all the

segments of the LCD and back light will light

up briefly.

Your anemometer is now operational.

Note:

After inserting the battery, test the anemometer by blowing directly at the Impeller

for about 30 seconds. The reading on the LCD should change. If is not the case,

remove the battery. Wait for 30 seconds, and re-insert the battery again.

Function keys:

The anemometer uses the following keys:

MODE/ key : Power ON/OFF

: To enter the setting node

: Back-light-On

+ Key : To change parameter in setting mode

(PLUS) : Back-light-On

LCD screen

Km/h mph m/s Kts

(Kilometers per hour) (miles per hour) (meters per seconds) (Knots)

Wind speed mode

The wind speed mode can be displayed into 4 different measurement scale in Km/h

(Kilometers per hour), mph (miles per hour), m/s (meters per seconds) or Kts

(Knots).

Power ON/OFF:

Press and hold down the “MODE/” key for 2 seconds to switch ON/OFF.

Note:

The anemometer is automatically switched OFF when no key is pressed in 34

minutes.

Manual setting

Before entering the manual setting mode, switch off the anemometer.

Press and hold down the “MODE/” key for about 4 seconds, the speed unit will

start flashing on the LCD when the manual setting mode is entered.

Measurement scale setting

1. After entering the manual setting mode, press “+” key to set the

measurement scale in Km/h (Kilometers per hour), mph (miles per hour), m/s

(meters per seconds) or Kts (Knots).

2. Now press the “MODE/” key to confirm and back to the normal mode.

LCD back-light:

The LCD back-light is automatically switched ON when any one of the 2 function

keys are pressed and held down about 2 seconds. The back-light will be switched

on for approximately 8 seconds before automatically switching OFF.

Fastening the necklace

The carry necklace is supplied with the anemometer.

To fasten, simply insert the clip of the necklace into the buckle end

of the anemometer until it clicks into place.

To unfasten, simply press both sides of the clip until it can be

removed from the buckle.

Battery change:

It is recommended to replace the battery in the unit on an annual basis to ensure

optimum accuracy of this unit.

Please help in the preservation of the environment. Return used

batteries to an authorised depot.

Maintenance:

· Avoid placing anemometer in areas prone to vibration and shock as these may

damage and inaccurate readings.

· Avoid exposure to sudden changes in temperature such as direct sunlight,

extreme cold and wet or moist conditions.

· When cleaning the display and casing, use a soft damp cloth only.

Do not use solvents or souring agents as they may mark the LCD and casing.

· Do not make or attempts to make any repairs to the anemometer. Return it to its

original point of purchase for repair by a qualified engineer. Opening and

tampering with the unit may invalidate its guarantee.

Specifications:

Wind speed measuring range : Minimum 0.2 m/s

Maximum 30 m/s

Wind speed accuracy : ±5% or ± least significant digit

Power source : 1 x 3V lithium cell (CR2032)

Battery life : Approximately 12 months

(The battery life might be shorter than 12

months depending on the use of the

backlight.)

Dimensions (L x W x H) : 39 x 17 x 98 mm

Liability Disclaimer:

· The manufacturer and supplier cannot accept any responsibility for any incorrect

readings and any consequences that occur should an inaccurate reading take

place.

· This product is not to be used for medical purposes or for public information.

· The specifications of this product may change without prior notice.

· This product is not a toy. Keep out of the reach of children.

· No part of this manual may be reproduced without written consent of the

manufacturer.

Battery cover

Battery

compartment

Battery

cover

+ key

MODE/ key

Impeller

Lithium

cell

(CR2032)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Techno line EA 3000 Anemometer Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info