Bedienungsanleitung Tecmate OPTIMATE 6 TM 180 (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

559312

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

example, with white matter between the plates, plates touching). If mechanical defects are apparent do not attempt to

charge the battery, have the battery professionally assessed.

5. If the battery is new, before connecting the charger read the battery manufacturer’s safety and operational instructions

carefully. If applicable, carefully and exactly follow acid ﬁ lling instructions.

USING THE OPTIMATE 6: PROCEEDING TO CHARGE

For safety reasons, the OptiMate output will only activate if a battery retaining at least 2V is connected, whereupon the

micro processor instantly diagnoses the battery condition and engages the appropriate charge mode and lights the

corresponding charge status LED.

The charger’s special recovery mode cannot engage if it senses that the battery is still connected to a vehicle wiring

circuit which effectively offers a lower electrical resistance than the battery on its own. However, if the deep-discharged

battery is not removed for recovery, neither battery nor vehicle electronics will be damaged.

VERY FLAT NEGLECTED BATTERIES: Pay particularly close attention to the following which is especially

important for relatively small batteries such as those used on motorcycles, lawn tractors, jet-ski’s, snowmobiles and

similar: A battery left deep-discharged for an extended period may develop permanent damage in one or more cells. Such

batteries may heat up excessively during high current charging.

Monitor the battery temperature during the ﬁ rst hour, then hourly there-after. Check for unusual signs, such as bubbling or

leaking electrolyte, heightened activity in one cell compared to others, or hissing sounds. If at any time the battery is

uncomfortably hot to touch or you notice any unusual signs, DISCONNECT THE CHARGER IMMEDIATELY.

ECO POWER SAVING MODE WHEN THE CHARGER IS CONNECTED TO AC SUPPLY: To reduce long term power

consumption OptiMate 6 employs two converter circuits, a power converter to charge the battery and an auxiliary converter to

power the control circuitry and LED display. The power converter is switched off when the charger is not connected to a battery

resulting in a very low power draw of less than 1,7W, equivalent to power consumption of 0,042 kWh per day. When a battery

is connected to the charger power consumption depends on the current demand of the battery and its connected vehicle /

electronic circuitry. After the battery has been charged and the charger is in long term maintenance charge mode (to keep the

battery at 100% charge) the total power consumption is estimated to be 0,060 kWh or less per day.

The LED indicators referred to below, and the clauses dealing with them, are sequenced as they may come on through

the course of the programme.

FINAL

TURBO

AMPS

ampmatic

LED #10

LED #8

LED #9

LEDs #5, 6 & 7

LEDs #1 & 2

LEDs #3 & 4

1 and 2. INVERSE connections and input power

1. Connect the charger to a mains supply socket providing AC supply of 220 to 240V. The “POWER ON” LED #1

should illuminate and LEDs #3,4,5,6,7 should blink twice to conﬁ rm micro processor health.

HIGH and LOW intensity indication: The "POWER ON" LED #1 will reduce intensity to a low level to indicate low power

"ECO" mode. This will occur if there is no battery connected, or when a battery is connected and the programme ﬁ nds

itself in the Initial and Extended voltage retention test mode or the 'rest' periods of Maintenance Charge mode. The

"POWER ON" LED #1 will indicate brightly during Recovery charge, Bulk and Pulsed absorption charge and

Maintenance charge modes.

2. If the INVERSE POLARITY LED #2 indicates, the battery connections are incorrect. The charger is electronically protected

so no damage will result, and the output will remain disabled until the connections are corrected.

3. Recovery charge

If the battery is extremely ﬂ at (deep-discharged and sulphated), the recovery mode will engage and the DESULFATE

LED #3 will light. A special high voltage is applied to force a very small ﬁ xed current into the battery in a recovery attempt that

may last for a maximum of two hours. Initially the voltage is limited to about 16V for 5 seconds while the circuit assesses

whether this level is sufﬁ cient to recover the battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tecmate OPTIMATE 6 TM 180 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tecmate OPTIMATE 6 TM 180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info