Bedienungsanleitung Telwin PRATICA 152 TURBO (Seite 7 von 84) (Alle Sprachen)

627106

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

- 7 -

couplings (if present), so as to ensure perfect electrical contact;

otherwise, the connectors will overheat, wear rapidly and become

inefcient.

- Use welding cables that are as short as possible.

- Do not use metal structures that are not part of the workpiece to

substitute the welding current return cable; this could endanger

safety and produce an unsatisfactory weld.

6.WELDING:DESCRIPTIONOFTHEPROCEDURE

These welding machines consist of a drooping specication, single

phase transformer and are suitable for welding with alternating

current using coated electrodes (E 43 R type) based on the diameters

given on the data plate.

To switch on the welding machine operate the main switch (Fig. B-1).

The intensity of the supplied welding current can be adjusted

continuously, by means of a manually operated magnetic shunt (Fig.

B-2).

The value of the current setting, (I

) can be read in Amps on the

graduated scale (Fig. B-3) on the top or side panel of machines

where it is provided.

THERMOSTATIC PROTECTION

This welder is automatically protected from thermic overheating

(thermostat automatic re-start). When the windings reach

performance temperature, the protections cut off the supply circuit,

igniting the yellow lamp on the front panel (Fig. B-4). After a few

minutes’ cooling the protection will reopen the supply line and turn off

the yellow lamp. The welder is ready for further use.

WELDING

- Use electrodes suitable for working in alternating current.

- The welding current must be regulated according to the diameter of

the electrode in use and the type of the joint to be carried out: see

below the currents corresponding to various electrode diameters:

Ø Electrode (mm)

Weldingcurrent(A)

min. max.

1.6 25 50

2 40 80

2.5 60 110

3.2 80 160

4 120 200

- The user must consider that, according to the electrode diameter,

higher current values must be used for at welding, whereas for

vertical or overhead welds lower current values are necessary.

- In addition to being determined by the selected current intensity,

the mechanical characteristics of the welded join are determined

by the other welding parameters i.e. arc length, working rate and

position, electrode diameter and quality (to store the electrodes

correctly keep them dry and protected by suitable packaging or

containers).

Weldingprocedure

- Holding the mask IN FRONT OF THE FACE, strike the electrode tip

on the workpiece as if you were striking a match. This is the correct

strike-up method.

 WARNING: do not hit the electrode on the workpiece, this

coulddamagetheelectrodeandmakestrike-updifcult.

- As soon as arc is ignited, try to maintain a distance from the

workpiece equal to the diameter of the electrode in use. Keep this

distance as much constant as possible for the duration of the weld.

Remember that the angle of the electrode as it advances should be

of 20-30 grades (Fig. D).

- At the end of the weld bead, bring the end of the electrode

backward, in order to ll the weld crater, quickly lift the electrode

from the weld pool to extinguish the arc.

CHARACTERISTICSOFTHEWELDBEAD

Fig. E

7. MAINTENANCE

WARNING! BEFORE CARRYINGOUT MAINTENANCE

OPERATIONS MAKE SURE THE WELDING MACHINE IS

SWITCHED OFF AND DISCONNECTED FROM THE MAIN

POWERSUPPLY.

EXTRAORDINARY MAINTENANCE

EXTRAORDINARY MAINTENANCE MUST ONLY BE CARRIED

OUT BY TECHNICIANS WHOARE EXPERT OR QUALIFIED IN

THE ELECTRIC-MECHANICAL FIELD, AND IN FULL RESPECT

OF THE IEC/EN 60974-4 TECHNICAL DIRECTIVE.

WARNING! BEFORE REMOVING THE WELDING

MACHINE PANELS AND WORKING INSIDE THE MACHINE

MAKESURETHEWELDINGMACHINEISSWITCHEDOFFAND

DISCONNECTEDFROMTHEMAINPOWERSUPPLYOUTLET.

Ifchecksaremadeinsidetheweldingmachinewhileitislive,

this may cause serious electric shock due to direct contact with

livepartsand/orinjuryduetodirectcontactwithmovingparts.

- Inspect the welding machine regularly, with a frequency depending

on use and the dustiness of the environment, and remove the dust

deposited on the transformer, using a jet of dry compressed air

(max. 10 bar).

- At the same time make sure the electrical connections are tight and

check the wiring for damage to the insulation.

- At the end of these operations re-assemble the panels of the

welding machine and screw the fastening screws right down.

- Never, ever carry out welding operations while the welding machine

is open.

- If necessary use a very thin layer of grease, at a high temperature,

to lubricate the moving parts of the regulators (threaded shaft,

sliding surfaces, shunts etc.).

- Replacingthepowersupplycable:before replacing the cable,

identify the screw-connecting terminals L1 and L2 (N) on the

switches (Fig. F).

- After having carried out maintenance or repairs, restore the

connections and wiring as they were before, making sure they do

not come into contact with moving parts or parts that can reach high

temperatures. Tie all the wires as they were before, being careful

to keep the high voltage connections of the primary transformer

separate from the low voltage ones of the secondary transformer.

Use all the original washers and screws when closing the casing.

Telwin PRATICA 152 TURBO Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info