Bedienungsanleitung Telwin PRO START 2824 (Seite 4 von 68) (Alle Sprachen)

649705

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

on the vehicle battery.

- Then connect the black clamp (-) to a non-movable

metal part of the engine; do not connect the clamp to

the negative terminal of the battery.

WARNING:DANGER!

These symbols warn operators that,

if the RED LIGHT comes on (Fig. A-1)

and the buzzer is triggered, this

indicates REVERSE POLARITY,

DANGER!

In these circumstances NEVER

switch on the starter, and remove the cables

immediately!

Make sure the vehicle battery and starter battery

polarities are correct before making the connections

described above.

- If there is no acoustic warning signal and the red light

is OFF, turn starter switch (Fig. C) to 12V or 24V (if

available) according to the voltage required by the

vehicle to be started.

- Turn the ignition switch or key of the vehicle or boat to

ON. Wait for about one minute. Turn the vehicle ignition

to the start position for no more than 3÷4 seconds. If the

vehicle or boat does not start, wait at least 3 minutes

before trying again.

Attention: do not allow the black and red

clamps to come into contact with each other

or to touch a common conductor.

While the engine is running, follow the whole sequence of

instructions below with great care:

1. Switch off the starter: switch to OFF position.

2. Disconnect the black (negative) clamp from the

vehicle.

3. Disconnect the red (positive) clamp from the vehicle.

4. Return the clamps to their housing.

It is highly recommended to recharge the starter as soon

as possible.

Usingthestarterasapowersupply:

- Take the cover off the cigar-lighter type socket (Fig.

A-2).

- Insert the cigar-lighter plug of the device to be powered

into the socket (Fig. A-2).

RECHARGING

Important! To protect the battery and lengthen its

working life, charge it for 12 hours before using it for

thersttime,thenaftereverytimeitisusedand,in

any case, at least every 3 months.

The unit can be recharged using a 230VAC power supply

(using the power supply adapter supplied) or using

a 12VDC power supply. We recommend keeping the

battery fully charged at all times. A low charge level could

shorten the life of the battery. Bear in mind that the time

needed to recharge the battery depends on the number

of times it has been used as a starter. To check whether

the battery needs recharging, press the switch seen in

g.A-3.

The three LED’s seen in Fig. A-4 indicate the charge

status of the battery, with the following meanings:

: the battery is very at;

: the battery is at;

: the battery is fully charged.

The red “Charging” LED (Fig. A-5) will light up when unit

is being charged.

The yellow “Remove Charger” LED (Fig. A-6) will light

up when unit is being charged to indicate that the control

device that protects the adaptor or batter has been

triggered. It is recommended to disconnect the adaptor

jack from the recharger socket.

Recharging using a 230V AC power supply

ATTENTION:Usethesuppliedpowersupply

adapter only!

1- To start with, insert the power supply adaptor plug

(Fig. B-7) into a 230V AC socket.

Then insert the relative output plug (Fig. B-8) into the

charger socket.

2- Check the switch in g.C is in the OFF position.

3- The “Charging” LED comes on and the starter is in

recharge mode. The starter is tted with a control

device to prevent overcharging the battery and

adaptor. Leave the system to recharge for as long as

necessary.

N.B.: to check the battery level disconnect the

adaptorandpressthebuttonseeninFig.A-3:The

LED’s seen in Fig. A-4 indicate the charge status of

the battery, with the meanings indicated above.

Recharging onboard the vehicle using 12VDC power

supply:

ATTENTION:Recharge the batterywhenthe

vehicle is running.

1- Check the switch in g.C is in the OFF position.

2- Insert the cigar-lighter plug of the supplied cable

(Fig. B-10) into the socket onboard the car or boat.

3- Insert the jack (Fig. B-9) of the supplied cable into

the recharger socket on the starter (Fig. A-7).

NOTE: this function is used to keep the charge level of

the starter as high as possible whilst travelling and may

not allow complete recharging.

DISPOSING OF THE BATTERY

When the starter battery is completely run down it should

be taken to a re-cycling depot. In some countries this is

mandatory. Contact the local special refuse authority for

information on recycling.

WARNING: Do not burn the battery to dispose of it.

This could cause an explosion. Before disposing of the

battery, apply insulating tape to the bare terminals to

prevent shorting. Do not expose the battery to intense

heat or re as this could cause an explosion.

SPECIFICATIONS:

STARTER 12V

Type of battery:

- Rechargeable factory-sealed 12V acid-lead battery.

Battery capacity:

- 34Ah

Output current.

- 1800A peak current;

Copper cables:

- PVC-insulated

Cable length:

- 100cm

Pilot lamp:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telwin PRO START 2824 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info