Bedienungsanleitung Teufel Columa 100 (Seite 3 von 4) (Englisch)

704027

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Setup and connection

Setup

Note

Our website contains comprehensive notes for correct setup.

• Select a stable, level base.

• Make sure that the environment is clean and free from dust.

• Avoid placing the unit close to sources of heat or in direct

sunlight.

• Arrange the connector cables so that they do not pose a trip

hazard.

• Do not place any heavy objects on the cables or the speaker.

Wall mounting

Attention

Risk of damage!

Improper assembly may result in damage.

• If mounting the speakers on the wall, make sure that the

installation is carried out expertly.

• Before drilling the holes, make sure that no pipes are

located within the drilling area using a metal detector.

• Only use suitable screws and dowels to mount the speak-

ers. Verify the carrying capacity of the walls.

• Hang the center speaker up on the wall using the keyhole

openings on the speaker back side and the screws you previ-

ously mounted.

• You can also use these openings for mounting a wall holder.

You can ﬁ nd suitable products for this in our web shop.

Connecting

Danger

Danger of injury/damage!

Arrange the cables so that they do not pose a

trip hazard.

• Pull the power plug of your AV receiver or multi-channel ac-

tive subwoofer out of the socket.

• Lay the speaker cables from your AV receiver or multi-chan-

nel active subwoofer to the speaker. These cables should be

high-quality double-wire speaker cable with marked strands.

The cross section should amount to at least 1.5 mm

• A connector comprising two terminals is located on the

back side of the speaker, to which you have to connect the

speaker cables.

• The terminal clips are each marked red (+) and black (-).

Make sure the polarity is correct!

Connect the like coloured terminals. Otherwise, the

sound quality will suffer.

The speaker connections of your AV receiver

or multi-channel

active subwoofer

should be marked similarly. The strands

of the speaker cables are marked with different colours or

shapes.

1. Split the single wire down to approx. 30 mm on both ends

and strip approx. 10 mm of insulation off of each cord.

2. Twist the stripped single wire ends together so that no wire

protrudes. Tin coating is not necessary.

3. Turn the connector terminal counterclockwise until loose.

Run the stripped cable end into the now visible hole. Close

the terminal by turning it counterclockwise. The cable has

now been clamped in place.

4. Connect the speaker cable to your AV receiver or multi-

channel active subwoofer. The operating instructions of the

appliance should contain notes on this.

Crossover frequency

The ideal separation frequency on the AV ampliﬁ er or multi-

channel active subwoofer for this speaker is 150 Hz.

91565 C GB 20120124.indd 391565 C GB 20120124.indd 3 24.01.12 14:1724.01.12 14:17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel Columa 100 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Teufel Columa 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info