704027
3
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
Preparation
Mounting the base plate
The base plate ensures a safe position of the speaker and it
minimises vibrations
. You need a Phillips head screwdriver of
size 0 for assembly.
Place the base plate on the speaker bottom carefully and
screw tighten it with 3 screws .
Make sure that the screws t precisely into the threaded
holes of the speaker and don’t pull the screws too tight.
Setup and connection
Setup
Note
Our website contains comprehensive notes for correct setup.
Select a stable, level base.
Make sure that the environment is clean and free from dust.
Avoid placing the unit close to sources of heat or in direct
sunlight.
Arrange the connector cables so that they do not pose a trip
hazard.
Do not place any heavy objects on the cables or the speak-
ers.
Make sure that the speaker has a stable position to prevent
vibrations.
Connecting
Danger
Danger of injury/damage!
Arrange the cables so that they do not pose a
trip hazard.
Pull the power plug of your AV receiver or multi-channel ac-
tive subwoofer out of the socket.
Lay the speaker cables from your AV receiver or multi-
channel active subwoofer to each speaker. These cables
should be high-quality double-wire speaker cable with
marked strands. The cross section should amount to at least
1.5 mm
2
.
A connector comprising two terminals is located on the
back side of each speaker, to which you have to connect the
speaker cables.
The terminal clips are each marked red (+) and black (-).
Make sure the polarity is correct!
Connect the like coloured terminals. Otherwise the
sound quality will suffer.
The speaker connections of your AV receiver or
multi-channel
active subwoofer
should be marked similarly. The strands
of the speaker cables are marked with different colours or
shapes.
1. Split the single wire down to approx. 30 mm on both ends
and strip approx. 10 mm of insulation off of each cord.
2. Twist the stripped single wire ends together so that no wire
protrudes. Tin coating is not necessary.
3. Turn the connector terminal counterclockwise until loose.
Run the stripped cable end into the now visible hole. Close
the terminal by turning it counterclockwise. The cable has
now been clamped in place.
4. Connect the cables to the other speaker in the same way.
5. Connect the speaker cables to your AV receiver or multi-
channel active subwoofer. The operating instructions of the
appliance should contain notes on this.
Crossover frequency
The ideal separation frequency on the AV ampli er or multi-
channel active subwoofer for the column speakers is 150 Hz.
91565 SS GB 20120124.indd 391565 SS GB 20120124.indd 3 03.02.12 10:2603.02.12 10:26
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Teufel Columa 100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Teufel Columa 100

Teufel Columa 100 Zusatzinformation - Englisch - 8 seiten

Teufel Columa 100 Zusatzinformation - Englisch - 4 seiten

Teufel Columa 100 Bedienungsanleitung - Englisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info