Bedienungsanleitung Teufel LT5 Mk2 FR (Seite 3 von 4) (Englisch)

562469

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Preparation

Mounting the base plate

The base plate with spikes ensures a safe position of the

speaker, minimises vibrations and provides enough room for

routing the wires

You need a Phillips head screwdriver of size PH2 for assembly.

1. Lay the speaker with the back side on a soft, padded base

carefully (e.g. on the polystyrene pads from the packaging).

2. Place the base plate b on the speaker bottom carefully and

screw tighten it with 4 washers d and 4 screws c.

3. Screw the knurled nut f on the threads of the spikes e,

then screw the spikes into the threaded holes in the base

plate.

4. To compensate for uneven oors slightly unscrew the spikes

and x them with the knurled nuts.

5. In the event of soft or sensitive oors, place a washer g

under each spike.

6. Make sure that the speakers have a stable position to pre-

vent vibrations.

Setup and connection

Setup

Note

Our website contains comprehensive notes for correct setup.

• Select a stable, level base.

• Make sure that the environment is clean and free from dust.

• Avoid placing the unit close to sources of heat or in direct

sunlight.

• Arrange the connector cables so that they do not pose a trip

hazard.

• Do not place any heavy objects on the cables or the spea-

kers.

• Make sure that the speaker has a stable position to prevent

vibrations.

Connecting

Danger

Danger of injury/damage!

Arrange the cables so that they do not pose a

trip hazard.

• Pull the power plug of your AV receiver or multi-channel ac-

tive subwoofer out of the socket.

• Lay the speaker cables from your AV receiver or multi-

channel active subwoofer to each speaker. These cables

should be high-quality double-wire speaker cable with marked

strands. The cross section should amount to 1.5 to 4mm

• A connector comprising two terminals is located on the

bottom of each speaker, to which you have to connect the

speaker cables.

• The terminal clips are each marked red (+) and black (-).

Make sure the polarity is correct!

Connect the like coloured terminals. Otherwise the

sound quality will suffer.

The speaker connections of your AV receiver or

multi-channel

active subwoofer

should be marked similarly. The strands

of the speaker cables are marked with different colours or

shapes.

1. Split the single wire down to approx. 30 mm on both ends

and strip approx. 10 mm of insulation off of each cord.

2. Twist the stripped single wire ends together so that no wire

protrudes. Tin coating is not necessary.

3. Turn the connector terminal counterclockwise until loose.

Run the stripped cable end into the now visible hole. Close

the terminal by turning it counterclockwise. The cable has

now been clamped in place.

4. Connect the cables to the other speaker in the same way.

5. Connect the speaker cables to your AV receiver or multi-

channel active subwoofer. The operating instructions of the

appliance should contain notes on this.

Crossover frequency

The ideal separation frequency on the AV amplier or multi-

channel active subwoofer for the column speakers is 100 Hz.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel LT5 Mk2 FR Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info