Bedienungsanleitung Texas HTP 2200 (Seite 13 von 17) (Englisch, Dänisch)

636740

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Adjusting the idle speed

First, check that the air filter is clean, as it can effect the

result.

When the idle speed is correct, the cutting blade should

not mowe, when machine is idling.

If adjustment is required, the idle screw (1) can be

adjusted. See Fig. 16,

Follow below procedure:

1. Close (turn counter clockwise) the idle adjustment

screw, with the engine running, until the cutting

attachment starts to rotate.

If the ildle speed cannot be adjusted so that the cutting

blade stops mowing. Contact your dealer/service

center. Do not use the machine until it has been

correctly adjusted or repaired.

Adjusting engine speed

Engine speed can be adjusted by following below

procedure (Fig. 19):

4. Adjust the screw (1). Opening 1 ± 1/4

5. Turn counter clockwise (2) decreases speed

6. Turn clockwise (3) increases the speed.

It is recommended to let a authorized service center

adjust the engineed speed.

Fuel filter

When the engine runs short of fuel, check the fuel cap

and the fuel filter for blockage/dirt, and clean it before

new mixed fuel is added. See Fig. 17.

Technical specifications

Model HTP 2200

Engine 22.2 cc / 0.68 kW

Rotations per minut Max 10,000 rpm (no-load)

Bar length 60 cm

Cutting length 55 cm

Cutting width 28 mm

Fuel tank 0.44 liter

Weight 5.6 kg

Noise 107 dB(A)

Standard warranty terms and conditions

The warranty period is 2 years for private end users in

EU countries.

Products sold for commercial use, only have a warranty

period of 1 year.

The warranty covers material and/or fabrication faults.

Restrictions and requirements

Normal wear and replacement of wearing parts are

NOT covered by the warranty.

Wearing parts, which are NOT covered for more than

12 months:

• Knives/blade

• Cables

• Switches

• Membranes/gaskets

• Spark plugs

• Engine liquids (oil, gasoline, grease)

• Starter cords

• Filters

If you start the engine without adding correct fuel mix of

gasoline and 2-stroke oil, it will be damaged and cannot

be repaired and therefore not covered by the warranty.

The warranty does NOT cover damages/faults

caused by:

• Lack of service and maintenance

• Structural changes

• Exposure to unusual external conditions

• Damages to the bodywork, deck, handles, panels

etc.

• If the machine has been improperly used or

overloaded

• Wrong use of oil, gasoline, grease or other liquid

types, which are not recommended in this user

manual

• Bad or dirty gasoline, which results in

contamination of the fuel system

• Use of unoriginal spare parts.

• Other conditions where Texas cannot be held

responsible.

Whether a case is a warranty claim or not is

determined in each case by an authorized service

center.

Your receipt is your warranty note, why it should

always be kept safe.

REMEMBER: The purchase of spare parts as well as

any request for warranty repair, model number, year

and serial number should always been informed. It can

be found on the CE-label on the machine!

* We reserve the right to change the conditions and

accept no liability for any misprints

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas HTP 2200 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info