636720
12
Zoom out
Zoom in
Vorherige Seite
1/14
Nächste Seite
12
Replacement the trimmer cord
Fig.4
1. Press on each side of the line compartment. The lid may now be removed.
2. Dismount the roll simply by pulling it. Leave the spring on the spool. Remove any bits of line.
3. Take 3-4 meters of new line (2,4 mm) and place it double in a loop-
4. Fit the loop in the middle of the spool and wind the nylon lines around the spool in each groove
without twisting the line. Follow the direction of the arrows from bottom of the spool.
Do not overfill the spool!
5. Mount the line compartment in reverse order. First, fit the spring into its position. Then place the line
in the two metal mortises of the line compartment.
6. Mount the lid. Ensure that it is fitted securely. Cut of excess nylon line.
Operation
For moving the line forward you tap the trimmer head lightly against the ground while the engine
runs at full speed.
Hold the trimmer at an upright angle towards the area that is to be cut.
Stones and walls, and poles cause the line to be worn down very fast.
Small trees and bushes can be easily damaged by the brush cutter.
Start / Stop.
How to start
See fig. 6
1. Press and hold the button
2. Press and hold the button
How to stop the engine
1. Release all buttons.
Vibrations may travel up into the handle
during use. We therefore recommend taking
a break every 2 hours.
Storage
Storage the product in a dry environment. It is recommended to hang the product on a wall, ensuring it is not
supporting on any of the attachment tools.
Lubrication of hedge trimmer accessory
The gearbox is lubricated from the factory, but for every 30-hour operation Grease MUST be refilled. Top up
with grease type: MULTIFAK EP-0 using a grease gun (not included) on the lubrication nipple.
Texas part no. 90306500.
Please note that the gearbox must be lubricated at all-time (all parts)
The blades must be kept lubricated to prevent friction and to extend the durability. Lubricate the blades with
regular hedge trimmer oil.
Lubricating the chain on the chainsaw accessory
Let the chainsaw run idle for 2-3 min.
Place saw on a flat surface
Remove the lid.
Add chain oil in the chainsaw container (top up).
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Texas Smart Combi 100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info