Bedienungsanleitung Thane H2O mop X5 - KB-6622V (Seite 16 von 19) (Englisch)

536957

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

USER’S GUIDE

Never leave the H2O MOP X5™ unattended while plugged in.

For Best Results:

1) Sweep or vacuum floor prior to using the H2O MOP X5™.

2) To avoid puddling of water, the Microfiber Cloth must

be clean and dry for use. To replace the cleaning cloth,

proceed as follows: Let the cleaning cloth cool down,

remove cloth from unit, replace with a new Microfiber Cloth

(Optional Item) and continue use. Select low steam regulator

position.

3) To sanitize an area of your floor, leave the H2O MOP X5™

at high steam setting over the steam area for about 10 seconds,

but no longer than 15 seconds.

Do not carry out this procedure on heat and steam

sensitive floors.

• Never steam at one spot for too long. This can cause floor

surface damage.

• Do not put hands or feet under the steam mop. Unit gets very hot.

• During use a pulsing noise may be heard indicating that the mop is producing

steam. This noise is normal.

• There may be some minor “spitting” of water mixed with the steam. This is

also normal.

• The force and heat of the steam may adversely affect certain materials. Always

check the suitability of using the steam mop on a surface by carrying out a

preliminary test on a hidden area.

Thane Direct and its affiliated companies assume no liability for personal injury or

property damage resulting from the misuse of the H2O MOP X5™, including the

failure to comply with the instructions contained in this User Guide or provided by

the manufacturer or distributor of the treated surface.

NOTICE

IMPORTANT

WARNING

Make sure that the H2O MOP X5™ is unplugged.

1) Fill the Water Tank with water. Please refer to the “HOW

TO USE THE H2O MOP X5™” section in this manual.

Attach either the round nylon brush or the round copper brush as

explained in the “How to assemble Hand-Held Steamer” section in

this manual.

2) Select one of the following Steam Regulator positions:

1 – Low, 2 – Medium, 3 – High or 4 – Hot Spray.

You can change the Steam Regulator position and

the steam output while operating the H2O MOP X5™.

3) Once the unit has been fully assembled and filled with water, plug in

the Power Cord into a grounded electrical outlet.

RED light - Power Indicator will indicate when power is on.

Power Switch ( O / I ) is in the OFF ( O ) position (higher position).

Wait for the Ready-to-Use indicator to turn Green - approximately 20 - 30 seconds.

GREEN light will turn on when the steam mop is ready for use.

When the Ready-to-Use indicator light turns green press the Power Switch ( O / I )

to the ON ( I ) position (lower position).

The Hand-Held Steamer will start

emitting steam.

To stop emitting steam, turn OFF the

unit by pressing the Power Switch ( O / I )

again. If the Power Switch ( O / I ) is

pressed (lower position) prior to the

Ready-to-Use light indicator turning

green, water from previous use will

not be heated and will be forced out

by present steam.

HOW TO USE HAND-HELD STEAMER

ON (I)

Position

(Lower)

OFF (O)

Position

(Higher)

Red - Power ON

Green - Ready to use

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thane H2O mop X5 - KB-6622V Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thane H2O mop X5 - KB-6622V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info