Bedienungsanleitung Thane H2O Steam FX Pro - KB-009C (Seite 5 von 9) (Englisch)

703158

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

8 9

Instructions for Assembly and Use Optional Accessory Usage

Assembling the Mop Accessory

1. Assemble the 3 Extension Pipes by ﬁtting the steam outlet

into the opening of the next Extension Pipe and the ﬁnal

Extension Pipe into the Mop Head as indicated in Fig. A.

Tip: You can adjust the height of the unit by using 2

Extension Pipes instead of 3.

2. Attach the Extension Pipe to the Steam Outlet of the

main unit as shown in Fig. B.

3. Attach the Mop Cloth to the Mop Head by attaching it to

the underside of the Mop Head as shown in Fig. C

4. When using the H2O SteamFX™ Pro on carpeting or

rugs; Place the Mop Head with Microﬁber Cloth in place,

on top of the Carpet Glider as illustrated. Do not attempt to

use the H2O SteamFX™ Pro on carpeting or rugs without

the Carpet Glider in place. Only use the microﬁber cloth on

carpets. Never use the Carpet Glider on surfaces that are

prone to scratching.

5. When ﬁnished remove the Mop Cloth from the Mop Head

and wash as needed.

WARNING:

Before using, make sure the mop has been assembled with

Mop Cloth attached to the Mop Head to prevent damage.

Notice: This product emits steam and creates moisture.

Water marks, discoloration or damage to the ﬂoor surface

can occur if the unit is left operating too long in one place.

Never leave the H2O SteamFX™ Pro Handheld Steamer

unattended while plugged in.

For Best Results:

1. Sweep or vacuum ﬂoor prior to using the H2O SteamFX™ Pro Handheld Steam

Cleaner.

2) To avoid puddling of water, the Microﬁber Cloth must be clean and dry for

use. To replace the cleaning cloth, proceed as follows: Let the cleaning cloth

cool down, remove cloth from unit, replace with a new Microﬁber Cloth

(Optional Item) and continue use.

3) To sanitize an area of your ﬂoor, leave the H2O SteamFX™ Pro Handheld

Steam Cleaner over the steam area for about 10 seconds, but no longer than

15 seconds. Do not carry out this procedure on heat and steam sensitive ﬂoors.

• Never steam at one spot for too long. This can cause ﬂoor surface damage.

• Do not put hands or feet under the steam mop. Unit gets very hot.

• During use, a pulsing noise may be heard indicating that the mop is

producing steam. This noise is normal.

• There may be some minor “spitting” of water mixed with the steam. This is

also normal.

• The force and heat of the steam may adversely affect certain materials.

Always check the suitability of using the steam mop on a surface by

carrying out a preliminary test on a hidden area.

Fig (A)

Fig (B)

Fig (C)

1. Find the Water Tank located in

the box. Remove the Water Tank

Cap and ﬁll with water to the “MAX”

ﬁll indicator line on the water tank,

and then secure the water tank cap

in place. Place under the main unit

and screw into position following

the Lock & Unlock marking on the

Water Tank

2. Attach an accessory to

Steam Outlet as indicated in the

“Accessories Usage” section.

3. Plug the appliance into an

electrical outlet. The Red Indicator

Light will turn ON.

4. Wait approximately 20-30

seconds. When the steamer is

ready to emit steam the Green

Indicator Light will turn ON. Press

and hold the Steam Switch

to emit steam.

Note: During usage the Green

Indicator Light will turn OFF when

the appliance re-heats and will

turn ON again once it reaches the

operating temperature. However,

the appliance will continuously

emit steam, as long as the Steam

Switch is pressed and water tank

is ﬁlled with water, regardless if the

Indicator turns ON.

RED light will remain ON when

plugged in.

IMPORTANT! Do not touch the

nozzle or any other attachments as

they can get hot.

5. Slowly Pass over the surface to

be cleaned.

6. To stop emitting steam release

the Steam Switch button.

IMPORTANT: After the Steam

Switch is turned OFF steam will

continue to ﬂow for a short period

of time (approximately 10 – 15

seconds) until all steam inside the

entire system is released.

7. When the appliance stops emitting

steam it means that the Water Tank

needs to be reﬁlled. Release the

Steam Switch button and unplug the

appliance from the electrical outlet.

Fill the Water Tank with water as

described in step 1 and then follow

steps 3-5 above.

Using the Safety Lock:

The Safety Lock can be used 2 ways.

1. Press the Safety Lock to the locked

position when the unit is

powered on to prevent accidentally

activating the Steam Switch to

produce steam.

2. Press the Safety Lock to the locked

position when pressing the

Steam Switch down to produce steam.

This allows you to release your thumb

from the Steam Switch. Simply click

the Steam Switch again or press down

on the Safety Lock to deactivate it and

stop the steam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thane H2O Steam FX Pro - KB-009C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info