23
GB
GB
AAA
Thank you for your decision for aThomson product.
Take your time and read the following instructions
and information completely. Please keep these
instructions in asafe place for future reference.
This re mote control can by default control 90%
models of SAMSUNG brand, there´s no need to set
it up. lf the re mote doesn‘t work, please choose
one of the setup methods described in chapter 5.
1. Input signal source /Indicator LED
2. POWER TV ON /OFF
3. Sw itch to signal sour PC
4. Sw itch to signal sour TV
5. Sw itch to signal sour HDMI
6. Numeric keys 0–9tenter channel
numbers
7. Previous channel
8. Ac cess to 2- or 3- digit channel numbers
9. TV Mute
10. Channel up/down
11. Te letext ON /OFF /MIX
12. Smart TV Menu
13. Change your TV‘s volume
14. Media Player
15. Show the Electr Pr Guide
(if supported by the TV)
16. Pr MENU
17. TO OLS MENU
18. On-Scr Info
19. Use when watching TV to see what‘s on
other channels or to highlight/Select
On-Screen options
20. Return /Back key
21. Tu rn off the menu of the selected product.
22. Use to select avariety of on screen options
23. Sound Mode
24. PictureMode
25. Multi Sound
26. Fa vorite Channel
27. PictureSize
28. 3D Mode ON/OFF
29. Suspends play and stops on an image
(DVD, BlueRay…)
30. Fa st Fo rward(DVD, BlueRay ... )
31. Goes backward(DVD, BlueRay ... )
32. St op the disc (DVD, BlueRay ... )
PIP (Pictureiicture)
33. Play adisc (DVD, BlueRay ... )
PIP Po sition
34. Recor
SWAP PIP
This symbol is used to indicate safety instructions
or to draw your attention to specic hazards
and risks.
This symbol is used to indicate additional
information or important notes.
•Replacement Remote Control
•2xAAA Batteries
•This operating instructions incl. Code List
•Donot use the Universal Remote Control in
moist or wet environments and avoid spray-
water contact.
•Donot expose the Universal Remote Control
to heat sources or direct sunlight.
•Donot drop the Universal Remote Control.
•Never open the Universal Remote Control. It
contains no user-serviceable parts.
•Aswith allelectrical devices, keep the
Universal Remote Control away from
children.
•When inserting batteries, note the
correct polarity (+ and -markings) and
insert the batteries accordingly.Failuret
do so could re sult in the batteries leaking
or exploding.
•Donot short-circuit batteries.
•Donot charge batteries.
•Donot throw batteries in are.
•Keep batteries out of the re ach of
children.
•Donot allow children to change batteries
without supervision.
•Remove the batteries from products
that arenot being used for an extended
period.
•Use 2AAA batteries
•Remove the battery cover from bottom
of re mote.
•Check the +/- polarity on the batteries
and inside the compartment.
•Insert the batteries.
•Slide the battery holder back into the
remote until the clips locate.
This re mote control saves the settings during
battery change.
This re mote control can by default control 90%
models of SAMSUNG brand, there´s no need to
set it up. lf it doesn‘t work, please choose one
of the following setup methods 5.1 or 5.2.
1. Press and hold the key [MUTE] and
[POWER] until the LED will be lit,
then re lease keys.
2. Enter the three codes from code Iist.
When the code input is nished, the
LED will turn off.
3. Please try to use the re mote control.
lf it doesn‘t work well, please try other
codes: [002], [003], [004] ...
lf the code is invalid, the LED ashes twice
and then lights up permanently.Txit the
setup, please press [MUTE].
1. Press and hold the key [MUTE] and
[POWER] until the LED will be lit, then
release keys.
2. Press the key [CH+]. Each time you
press, the re mote will search once.
When the code changes, you can test
if [POWER], [VOL+],[MENU],[0-9] keys
work well. If ok ,please press [MUTE] to
save the code and exit.
3. lf it doesn‘t work well, re peat the fast
search by pressing [CH+].
Use the following method to nd out which
code is currently set:
1. Press and hold [MUTE], then press
[POWER] until the LED will be lit, then
release keys.
2. Input [9].[9].[0] with number keys. The
LED will ash twice and goes off
3. Press the number key 1for the 1st digit
of the code. The LED will start to ash.
Count the LED ashes. The number of
ashes re semble the code‘s rst digit.
Repeat this procedurefor the 2nd and
3rddigit of the code:
2nd digit -> enter 2->count LED
ashes
3rddigit -> enter 3->count LED ashes
lf code number is [0] the LED will not
ash.
Due to too many Remote Control models, we
only Iist some of them below.
lf your remote control is similar to the drawing,
the replacement remote can control your TV
(Page 74).
Press and hold the [RETURN] and [0] buttons for
about 5seconds until the status LED flashes three
times and then goes out. The remote control is
now successfully reset to the factory settings.
All keys with learnt codes or all copied keys,
as well as all remote control settings will
be deleted.
This remote control is equipped with alearning
function. Thus, you could learn functions of
your original remote to this remote control.
•The batteries in the two re mote controls
have to be in good condition. Replace them
if necessary.
•Place the re mote controls with the infrared
diodes so that they point towards each
other
•Wherenecessary adjust the height of both
remotes so that infr diodes areproperly
aligned.
•The distance between the re mote controls
should be about 3cm.
•Donot move the re mote controls during
the learning procedure.
•E
nsur
et
hat
the
ro
om
is
not
lit
by
uor
escents
tubes
or
low
ener
gy
consumption lamps since such light
sources could interferewith the copying.
•The 2remotecontrols must be at least
1meter away from any light source.
•During learning mode, if no key is
selected for morethan 15 seconds, the
learning mode will exit automatically or
if no other re mote signal is re ceived.
•Each function key will hold only one
command. Anew command to be learned
will automatically re place the pr one.
1. Pr and hold the [MUTE] and [VOL+]
keys for approx. 5seconds until the LED
will be lit.
5
2. Enter the code [9] [8] [0], the LED will ash
2times and then re main on.
3. The re mote contr is now re ady to learn
new commands.
1. Pr and re lease the desired key on the
original re mote control which you want the
command to be learned. The LED at your
replacement re mote will ash to conrm
that the information has been re ceived.
ca. 3c
ORIGINAL
