ROC1309
00131871
Operating Instructions
Mode d‘emploi ....................................................................... 03
Bedienungsanleitung
Istruzioni per l‘uso
Instrucciones de uso
Gebruiksaanwijzing
Manual de instruções 13
Οδηγίες χρήσης..................................................................... 15
Руководство по эксплуат . ........................................ 17
Instrukcja obsługi 19
Návod k použití . ..................................................................... 21
Használati útmutató 23
Bruksanvisning
Brukerveiledning
Brugsanvisning
Pistokelaturi
1
GB
1
3
4
6
9
8
8
16
12
14
2
11
15
13
5
7
7
10
Characteristics - Caractéristiques - Eigenschaften - Caratteristiche
Características - Eigenschappen - Características - χαρακτηριστικά
Технические характе ристики - Dane techniczne - Technické údaje
Karakterisztika - Data - Karakteristikker - Data - Ominaisuudet
Dimensions - Dimensions - Abmessungen - Dimensioni
- Afmetingen - Dimensões - Διαστάσεις - размеры -
Wymiary - Rozměry
- Méret
- Mått - Dimensjoner - Mål - Mitat
= 171 x 49 x 20 mm
Weight = 80 grammes
Poids = 80 grammes
Gewicht = 80 Gramm
Peso = 80 grammi
Peso = 80 gramos
Gewicht = 80 gram
Peso = 80 gramas
Βάρoς = 80 γραμμάρια
вес = 80 грамм
Ciężar = 80 g
Hmotnost = 80 g
Súly = 80 gramm
Vikt = 80 gram
Vekt = 80 gram
Vægt = 80 gram
Paino = 80 grammaa
AAA
This y, so
of the group’ For reason, recommend prior
attempting to programme
described in this user manual. Howeverfi rst of all, you must install 2 batteries (AAA) in the
remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
1 Indicator light: The red indicator light is lit
whenever a key is pressed.
2 G : On/Standby or Standby only
the equipment being used.
3 The coloured buttons can be used to select
categories when teletext is activated, and specifi c
functions depending on the make.
4 : T
: T
: T
: Displays information of the selected
appliance.
5 Guide: Electronic Program Guide.
6 Setup: Allows you to program your remote
before the fi rst use.
7 P+/P-: Channel Up and Channel Down buttons.
8 V+/V-: Increases (+) or decreases (-) the volume
of the selected device.
9 OK: Confi rms a selection.
10 C /D /A /B : Allow you to navigate the menus
verticaly and horizontaly
11 Exit: T
12 H (Mute): Switches the selected appliance sound
off.
13. Menu: T
14 Numeric keys 0-9: These keys have the same
functions as those of your original remote and
are also used to enter the code.
15 :--/-: In connection with the numeric keys, this
button allows you, with some equipment, to select
directly channels with 2 digits.
16 AV : For selecting an exterT,
HDMI, ...)..
Note: depending on the actual devices, manufacturers
and year of manufacture, the functions available
will vary.
The keys
Testing the remote control before
you programme it
1. Switch on the set you want to control.
2. Direct the remote control towards the TV set and
try to switch it ofG . If
the device does not turn off, you must program the
remote control using one of the methods A, B, C or
D described hereafter
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must fi nd the
subcode of the set to be controlled. Entering a subcode
lets the remote control test a predefi ned list of codes.
Refer to the list provided with these instructions, page I
of the subcodes .
1.
2. SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time to
proceed with the following steps. The indicator lamp
fl ashes to signal that this time is almost up, and then
goes off). Release the SETUP key
3.
(example: 1 for THOMSON).
4.
switch it off by pressing the key G .
5. OK
to memorise the code.
6. G repeatedly
until the set switches off. Between pressing the keys,
be sure to leave enough time for the indicator light to
go out and then relight (about 1 second). Proceeding
this way will enable you to see whether the set
responds or not.
7.
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2 .
Method B – 4-digit codes
programming
Before you start programming, you must fi nd the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time to
proceed with the following steps. The indicator lamp
fl ashes to signal that this time is almost up, and then
goes off). Release the SETUP key
3. While the indicator is lit, enter the fi rst digit of the
4-digit code proposed for the set to be controlled
(example: 0036 for Thomson).
4. Direct the remote control towards the set and try to
switch it off by pressing the key G .
5. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the set
by pressing key G once. Repeat this procedure by
trying out each of the 4-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2 .
00131871bda.indd 4-Abs1:100131871bda.indd 4-Abs1:1 05.10.2009 14:45:22 Uhr05.10.2009 14:45:22 Uhr
