Bedienungsanleitung Thomson ROC2306 2in1 (Seite 3 von 3) (Englisch)

607837

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

1. S witch on the COMBO you want to control.

2. Hold down the S (10) until the red indicator

lamp (1) remains lit (the indicator light remains on

for a few seconds to give you the time to proceed with

the following steps. The indicator lamp flashes when

this time is almost up, and then goes off).

3. Press the TV (3) key, then follow one of the

programming methods (A, B, C or D) described

earlier.

4. I f a second code programming is required, then repeat

steps 2 and 3 above.

4 - How to retrieve

a programmed code

It may be useful to retrieve the code programmed in the

remote control.

1. Hold down the S (10) until the red indicator lamp

(1) remains lit (the indicator light remains on for a

few seconds to give you the time to proceed with the

following steps. The indicator lamp flashes when this

time is almost up, and then goes off).

2. P ress the key (3) that corresponds to the type of

equipment you want to control:

TV: television set,

VCR/DVD: video cassette recorder, DVD player.

3. Press S (10) again briefly. The red indicator lamp

(1) flashes once.

4. Press the number keys (0 to 9) in ascending order

until the red indicator lamp (1) flashes once.

5. The digit which made the red indicator lamp (1) flash,

is the first number of the 4-digit code. Please make

note of it.

6. R epeat step 4 to find out the other numbers of the

code.

7. When the fourth number is found, the red indicator

lamp (1) goes off.

5 - Check of the programming

- F or a television or a satellite receiver: switch on and, for

example, press (15) to change channels.

- D VD player: load a DVD and then press PLAY (6).

Tr y other remote control keys to find out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of your set, jot

it down so that you can use it whenever needed.

After battery replacement, you may have to

programme the remote control again.

7 - The NAVILIGHT system

The THOMSON NAVILIGHT navigation system allows you

easy access to the settings of your television set (TV) or your

video recorder (VCR) fitted with the THOMSON NAVILIGHT

system provided that you have allocated the VCR/DVD key

to the video recorder.

1. S witch on the set you want to control.

2. P ress the key corresponding to the type of set you

want to use (TV or VCR/DVD). In the VCR/DVD

position, make sure that the AV mode is activated for

the TV set (the SCART socket must be selected).

3. Press the S (10) key once and then press the a (16)

key.

4. N avigate through the setting menus with the play keys

p, q, t and u (9 and 15).

5. Validate with OK (14).

6. T o leave the menus, press key EXIT (8) once.

Note: The S (10) key remains on as long as light I is lit. If this

light goes out, you have to press the S (10) key again before

using the navigation keys. To exit this mode, press S (10) a

second time.

ROC 2306 / EN / aws - rst / 12-2006

6 - Other functions

Adjustment of ALL volume controls under a

specific mode.

Yo u can allocate the volume control to one of the modes

of the remote control on condition that the volume

control exists on the corresponding device (e.g. control of

TV sound in VCR/TV mode).

1. H old down the S (10) key until the red indicator

lamp (1) remains lit.

2. Release the S (10) key.

3. P ress the c (14) key. The red indicator lamp (1)

flashes once.

4. P ress once on the mode key (TV, VCR/DVD…)

corresponding to the device whose volume will always

be controlled by the VOL (9) and c (14) keys.

5. Press the c (14) key once.

Adjustment of the volume controls for EACH

mode.

Yo u can decide that the volume control is functional for

each mode selected on condition that the volume control

exists on the corresponding device (e.g. control of the

television set sound in TV mode, the control of the sound

of the SAT receiver in SAT mode, ...).

1. Hold down the S (10) key until the red indicator

lamp (1) remains lit.

2. Release the S (10) key.

3. Press the c (14) key. The red indicator lamp (1)

flashes once.

4. Press once on the mode key (TV, VCR/DVD…)

corresponding to the device whose volume will always

be controlled by the VOL (7) and c (14) keys.

5. Press the VOL - (9) key once.

6. Press the c (14) key once.

TV CODE VCR/DVD CODE

Yo u can contact THOMSON by dialling:

0871 500 0520

(call to this number

will be charged at 10 pence per minute)

www.thomsonlink.com

01_ROC2306_GB.indd 3 7/12/06 10:13:36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson ROC2306 2in1 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC2306 2in1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info