Bedienungsanleitung Thomson ROC4407 4in1 (Seite 2 von 3) (Englisch)

607834

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

How to retrieve

a programmed code

Method C – Programming by means

of code retrieval

Method D - Automatic

code search

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit.

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player,

VCR: video recorder,

STB: satellite receiver, cable, DVBT, ADSL

4. Direct the remote control towards the set

and try to

switch it off by pressing the key

5. If the set you want to control switches off, press OK

to memorise the code.

6. Should the set not switch off, press key

as many

times as required (up to 200 times), until the set

switches off. Between two key presses, leave

enough time for the key corresponding to the

selected mode enough time to light up again (about

1 second). Proceeding this way will enable you to

see whether the set responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Try out other remote control keys to find out the range

of functions you can control. If you think that not all of

the keys are active, repeat the procedure of this

programming method to find out the code supporting a

wider range of features.

With this method, the remote control scrolls through the

full code list by sending an IR signal to the set to be

controlled remotely. Proceed as follows:

1. Check that your equipment is on. If not, switch it on

manually.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks and

then remains lit (the indicator light remains on for a

few seconds to give you the time to proceed with the

following steps. The indicator lamp flashes to signal

that this time is almost up, and then goes off).

3. Release the SETUP key.

4. Press the key corresponding to the type of

equipment (for example TV).

5. Press the PROG+ or standby

(DVD/VCR only) key. After a few seconds, the

remote control begins to scroll through the whole

code list included in the library (at a rate of roughly

1 code per second). Press the PROG+ key once

again to slow down the test speed (1 code every 3

seconds). As soon as the set changes channels, you

must press OK to save the code and stop the

remote control scrolling through the list. If you do

not react quickly enough, you can go back to the

previous code by pressing PROG- or

(DVD/VCR only) as many times as necessary (you

can go forward by pressing

, PROG+ or

(DVD/VCR only) if you have gone back too far).

As soon as the set responds again, press OK to

save the code.

It may be useful to retrieve the code programmed in the

remote control.

1. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit.

2. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player,

VCR: video recorder,

STB: satellite receiver, cable, DVBT, ADSL.

3. Press the SETUP key briefly, so that the last mode

selected blinks once.

4. Press the numbered keys in ascending order (0 to

9) until the selected mode blinks once.

5. The number that caused the selected mode to blink

is the first of the four numbers that make up your

code. Make a note of it below.

6. Repeat step 4 to find out the other numbers of the

code.

7. When the fourth number has been found, the

indicator light for the selected mode goes out.

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the set

by pressing key

once. Repeat this procedure by

trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Check of

the programming

- For a television or a satellite receiver: switch on and,

for example, press 2 to change channels.

- Video recorder: load a tape and then press

- DVD player: load a DVD and then press

Try other remote control keys to find out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of your

set, jot it down so that you can use it

whenever needed.

After battery replacement, you’ll have to

programme the remote control again.

Method E – Programming for control of

a COMBO (combined TV-VCR,TV/DVD,

VCR/DVD, … set)

Depending on the COMBO group (TV/VCR,

VCR/DVD, etc.) and the make, you will be required to

enter a single code for both devices in the COMBO, or

to enter two codes, one code per device. Consult the

separate list to discover this.

Before you start programming, you must find the

subcode or code of the subset to be controlled

(television or video recorder). Refer to the list supplied

with this user manual (see page subcodes or codes).

1. Switch on the COMBO you want to control.

2. Hold the SETUP key down until the key

corresponding to the last selected mode blinks and

then remains lit.

3. Press the key of the first device to control, and then

follow one of the programming methods A, B, C or

D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

VCR CODE

STB CODE

DVD CODE

TV CODE

F01_GB_ROC4407.qxp 22/01/07 16:49 Page 2

Thomson ROC4407 4in1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC4407 4in1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info